Home

RFC6751

  1. RFC 6751
Independent Submission                                   R. Despres, Ed.
Request for Comments: 6751                                     RD-IPtech
Category: Experimental                                      B. Carpenter
ISSN: 2070-1721                                        Univ. of Auckland
                                                                 D. Wing
                                                                   Cisco
                                                                S. Jiang
                                           Huawei Technologies Co., Ltd.
                                                            October 2012


 Native IPv6 behind IPv4-to-IPv4 NAT Customer Premises Equipment (6a44)

Abstract

   In customer sites having IPv4-only Customer Premises Equipment (CPE),
   Teredo (RFC 4380, RFC 5991, RFC 6081) provides last-resort IPv6
   connectivity.  However, because it is designed to work without the
   involvement of Internet Service Providers, it has significant
   limitations (connectivity between IPv6 native addresses and Teredo
   addresses is uncertain; connectivity between Teredo addresses fails
   for some combinations of NAT types).  6a44 is a complementary
   solution that, being based on ISP cooperation, avoids these
   limitations.  At the beginning of 6a44 IPv6 addresses, it replaces
   the Teredo well-known prefix, present at the beginning of Teredo IPv6
   addresses, with network-specific /48 prefixes assigned by local ISPs
   (an evolution similar to that from 6to4 to 6rd (IPv6 Rapid Deployment
   on IPv4 Infrastructures)).  The specification is expected to be
   complete enough for running code to be independently written and the
   solution to be incrementally deployed and used.





















Despres, et al.               Experimental                      [Page 1]
RFC 6751          Native IPv6 behind NAT44 CPEs (6a44)      October 2012


Status of This Memo

   This document is not an Internet Standards Track specification; it is
   published for examination, experimental implementation, and
   evaluation.

   This document defines an Experimental Protocol for the Internet
   community.  This is a contribution to the RFC Series, independently
   of any other RFC stream.  The RFC Editor has chosen to publish this
   document at its discretion and makes no statement about its value for
   implementation or deployment.  Documents approved for publication by
   the RFC Editor are not a candidate for any level of Internet
   Standard; see Section 2 of RFC 5741.

   Information about the current status of this document, any errata,
   and how to provide feedback on it may be obtained at
   http://www.rfc-editor.org/info/rfc6751.

Copyright Notice

   Copyright (c) 2012 IETF Trust and the persons identified as the
   document authors.  All rights reserved.

   This document is subject to BCP 78 and the IETF Trust's Legal
   Provisions Relating to IETF Documents
   (http://trustee.ietf.org/license-info) in effect on the date of
   publication of this document.  Please review these documents
   carefully, as they describe your rights and restrictions with respect
   to this document.






















Despres, et al.               Experimental                      [Page 2]
RFC 6751          Native IPv6 behind NAT44 CPEs (6a44)      October 2012


Table of Contents

   1. Introduction ....................................................3
   2. Requirements Language ...........................................5
   3. Definitions .....................................................5
   4. Design Goals, Requirements, and Model of Operation ..............7
      4.1. Hypotheses about NAT Behavior ..............................7
      4.2. Native IPv6 Connectivity for Unmanaged Hosts behind
           NAT44s .....................................................7
      4.3. Operational Requirements ...................................8
      4.4. Model of Operation .........................................9
   5. 6a44 Addresses .................................................12
   6. Specification of Clients and Relays ............................14
      6.1. Packet Formats ............................................14
      6.2. IPv6 Packet Encapsulations ................................14
      6.3. 6a44 Bubbles ..............................................14
      6.4. MTU Considerations ........................................16
      6.5. 6a44 Client Specification .................................16
           6.5.1. Tunnel Maintenance .................................16
           6.5.2. Client Transmission ................................19
           6.5.3. Client Reception ...................................20
      6.6. 6a44 Relay Specification ..................................23
           6.6.1. Relay Reception in IPv6 ............................23
           6.6.2. Relay Reception in IPv4 ............................24
      6.7. Implementation of Automatic Sunset ........................26
   7. Security Considerations ........................................26
   8. IANA Considerations ............................................30
   9. Acknowledgments ................................................30
   10. References ....................................................30
      10.1. Normative References .....................................30
      10.2. Informative References ...................................31

1.  Introduction

   Although most Customer Premises Equipment (CPE) should soon be dual-
   stack capable, a large installed base of IPv4-only CPEs is likely to
   remain for several years.  Their operation is based on IPv4-to-IPv4
   NATs (NAT44s).  Also, due to the IPv4 address shortage, more and more
   Internet Service Providers (ISPs), and more and more mobile
   operators, will assign private IPv4 addresses ([RFC1918]) to their
   customers (the [NAT444] model).  For rapid and extensive use of IPv6
   [RFC2460], there is therefore a need for IPv6 connectivity behind
   NAT44s, including those of the [NAT444] model.








Despres, et al.               Experimental                      [Page 3]
RFC 6751          Native IPv6 behind NAT44 CPEs (6a44)      October 2012


   At the moment, there are two tunneling techniques specified for IPv6
   connectivity behind NAT44s:

   o  Configured tunnels.  These involve tunnel brokers with which users
      must register [RFC3053].  Well-known examples include deployments
      of the Hexago tool, and the SixXS collaboration, which are
      suitable for IPv6 early trials.  However, this approach is not
      adequate for mass deployment: it imposes the restriction that even
      if two hosts are in the same customer site, IPv6 packets between
      them must transit via tunnel servers, which may be far away.

   o  Automatic Teredo tunnels [RFC4380] [RFC5991].  Teredo is specified
      as a last-resort solution that, due to its objective to work
      without local ISP involvement, has the following limitations:

      *  Connectivity between IPv6 native addresses and Teredo addresses
         is uncertain.  (As explained in [RFC4380] Section 8.3, this
         connectivity depends on paths being available from all IPv6
         native addresses to some Teredo relays.  ISPs lack sufficient
         motivations to ensure it.)

      *  Between two Teredo addresses, IPv6 connectivity fails for some
         combinations of NAT44 types ([RFC6081] Section 3).

      *  According to [RFC4380] Section 5.2, each Teredo host has to be
         configured with the IPv4 address of a Teredo server (a
         constraint that can, however, be avoided in some
         implementations).

   6a44 is designed to avoid Teredo limitations: with 6a44, ISPs can
   participate in the solution.  The approach for this is similar to the
   approach that permitted 6rd [RFC5569] [RFC5969] to avoid the
   limitations of 6to4 [RFC3056] [RFC3068]: at the beginning of IPv6
   addresses, the Teredo well-known prefix is replaced by network-
   specific prefixes assigned by local ISPs.

   This document is organized as follows: terms used in the document are
   defined in Section 3; design goals and model of operation are
   presented in Section 4; Section 5 describes the format of 6a44 IPv6
   addresses; Section 6 specifies in detail the behaviors of 6a44
   clients and 6a44 relays; security and IANA considerations are covered
   in Sections 7 and 8, respectively.

   This specification is expected to be complete enough for running code
   to be independently written and the solution to be incrementally
   deployed and used.  Its status is Experimental rather than Standards
   Track, to reflect uncertainty as to which major Internet players may
   be willing to support it.



Despres, et al.               Experimental                      [Page 4]
RFC 6751          Native IPv6 behind NAT44 CPEs (6a44)      October 2012


2.  Requirements Language

   The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
   "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
   document are to be interpreted as described in [RFC2119].

3.  Definitions

   The following definitions are used in this document:

   MAJOR NEW DEFINITIONS

   6a44 ISP network:  An IPv4-capable ISP network that supports at least
      one 6a44 relay.  Additional conditions are that it assigns
      individual IPv4 addresses to its customer sites (global or
      private), that it supports ingress filtering [RFC2827], and that
      its path MTUs are at least 1308 octets.

   6a44 relay:  A node that supports the 6a44 relay function defined in
      this document and that has interfaces to an IPv6-capable upstream
      network and to an IPv4-capable downstream network.

   6a44 client:  A host that supports the 6a44 client function defined
      in this document and has no means other than 6a44 to have an IPv6
      native address.

   6a44 tunnel:  A tunnel established and maintained between a 6a44
      client and 6a44 relays of its ISP network.

   6a44 bubble:  A UDP/IPv4 packet sent from a 6a44 client to the
      6a44-relay address, or vice versa, and having a UDP payload that
      cannot be confused with an IPv6 packet.  In the client-to-relay
      direction, it is a request for a response bubble.  In the relay-
      to-client direction, it conveys the up-to-date IPv6 prefix of the
      client.

   SECONDARY NEW DEFINITIONS

   (This list is for reference and can be skipped by readers familiar
   with the usual terminology.)

   6a44 service:  The service offered by a 6a44 ISP network to its 6a44
      clients.

   6a44-client IPv6 address:  The IPv6 address of a 6a44 client.  It is
      composed of the client IPv6 prefix, received from a 6a44 relay,
      followed by the client local IPv4 address.




Despres, et al.               Experimental                      [Page 5]
RFC 6751          Native IPv6 behind NAT44 CPEs (6a44)      October 2012


   6a44-client IPv6 prefix:  For a 6a44 client, the IPv6 prefix (/96)
      composed of the IPv6 prefix of the local 6a44 network (/48)
      followed by the UDP/IPv4 mapped address of the client (32 +
      16 bits).

   6a44-client UDP/IPv4 mapped address:  For a 6a44 client, the external
      UDP/IPv4 address that, in the CPE NAT44 of the site, is that of
      its 6a44 tunnel.

   6a44-client UDP/IPv4 local address:  For a 6a44 client, the
      combination of its local IPv4 address and the 6a44 port.

   6a44 port:  UDP port 1027, reserved by IANA for 6a44 (see Section 8).

   6a44-relay UDP/IPv4 address:  The UDP/IPv4 address composed of the
      6a44-relay anycast address and the 6a44 port.

   6a44-relay anycast address:  IPv4 anycast address 192.88.99.2,
      reserved by IANA for 6a44 (see Section 8).

   6a44-network IPv6 prefix:  An IPv6 /48 prefix assigned by an ISP to a
      6a44 network.

   USUAL DEFINITIONS

   (This list is for reference and can be skipped by readers familiar
   with the usual terminology.)

   Upstream direction:  For a network border node, the direction toward
      the Internet core.

   Downstream direction:  For a network border node, the direction
      toward end-user nodes (opposite to the upstream direction).

   IPv4 private address:  An address that starts with one of the three
      [RFC1918] prefixes (10/8, 172.16/12, or 192.168/16).

   IPv6 native address:  An IPv6 global unicast address that starts with
      an aggregatable prefix assigned to an ISP.

   UDP/IPv4 address:  The combination of an IPv4 address and a UDP port.

   UDP/IPv4 packet:  A UDP datagram contained in an IPv4 packet.

   IPv6/UDP/IPv4 packet:  An IPv6 packet contained in a UDP/IPv4 packet.






Despres, et al.               Experimental                      [Page 6]
RFC 6751          Native IPv6 behind NAT44 CPEs (6a44)      October 2012


4.  Design Goals, Requirements, and Model of Operation

4.1.  Hypotheses about NAT Behavior

   6a44 is designed to work with NAT44 behaviors identified in Section 3
   of [RFC6081].  In particular, it has to work with endpoint-dependent
   mappings as well as with endpoint-independent mappings, including
   cases where there are dynamic changes from one mode to the other.

   The only assumption is that, after a mapping has been established in
   the NAT44, it is maintained as long as it is reused at least once, in
   each direction, every 30 seconds.

   NOTE: 30 seconds is the value used for the same mapping-maintenance
   purpose in Teredo [RFC4380] and in SIP [RFC5626].

4.2.  Native IPv6 Connectivity for Unmanaged Hosts behind NAT44s

   The objective remains that, as soon as possible, CPEs and ISPs
   support IPv6 native prefixes.  6a44 is therefore designed only as a
   temporary solution for hosts to obtain IPv6 native addresses in sites
   whose CPEs are not IPv6 capable yet.

   As noted in Section 1, IPv6 native addresses obtainable with
   configured tunnels have important limitations.  However, compared to
   6a44 addresses, they have the advantage of remaining unchanged in the
   case of NAT44 reset.  6a44 therefore remains the last-resort solution
   for IPv6 native addresses in unmanaged hosts of IPv4-only-CPE sites,
   while configured tunnels may still be preferred for some managed
   hosts if reported limitations of configured tunnels are judged to be
   acceptable.  As their scopes are different, the two solutions can
   usefully coexist.

   Note that Teredo remains a last-resort solution for hosts to have
   IPv6 addresses where IPv6 native addresses cannot be made available
   (and where Teredo limitations are judged to be acceptable).















Despres, et al.               Experimental                      [Page 7]
RFC 6751          Native IPv6 behind NAT44 CPEs (6a44)      October 2012


4.3.  Operational Requirements

   Operational requirements of 6a44 include the following:

   Robust IPv6 connectivity:  A node having a 6a44 address must have
      paths across the Internet to and from all IPv6 native addresses
      that are not subject to voluntary firewall filtering.

   Intra-site path efficiency:  Packets exchanged between 6a44 clients
      that are behind the same CPE NAT44 must not have to traverse it.
      If these clients have IPv4 connectivity using their private IPv4
      addresses, they must also have IPv6 connectivity using their 6a44
      addresses.

   Plug-and-play operation of 6a44 clients:  In order to obtain a 6a44
      address from its local ISP, a 6a44 client must need no parameter
      configuration.

   Scalability of ISP functions:  For the solution to be easily
      scalable, ISP-supported functions have to be completely stateless.

   Anti-spoofing protection:  Where address anti-spoofing is ensured in
      IPv4 with ingress filtering [RFC2827] [RFC3704], IPv6 addresses
      must benefit from the same degree of anti-spoofing protection.

   Overall operational simplicity:  To paraphrase what Antoine de Saint-
      Exupery said in [TheTool], "it seems that perfection is attained
      not when there is nothing more to add, but when there is nothing
      more to remove".

   Incremental deployability:  Hosts and ISP networks must be able to
      become 6a44 capable independently of each other.  IPv6 must be
      operational where both are available, and there must be no
      perceptible effect where they are not both available.

















Despres, et al.               Experimental                      [Page 8]
RFC 6751          Native IPv6 behind NAT44 CPEs (6a44)      October 2012


4.4.  Model of Operation

   Operation of 6a44 involves two types of nodes: 6a44 clients and 6a44
   relays.  Figure 1 shows the two applicability scenarios:

   o  In the first one, IPv4 addresses assigned to customer sites are
      global IPv4.

   o  In the second one, they are private IPv4 addresses (the [NAT444]
      model, where ISPs operate one or several NAT44s, also called
      Carrier-Grade NATs (CGNs)).

                             (A) GLOBAL IPv4 ISP NETWORK
                                   +------------------+
        6a44 customer network(s)   |GLOBAL IPv4       |       Upstream
               +-----------+    ---| MTU >= 1308      +---  IPv4 network
            ---| Private   |       | ingress filtering|   (<== no route
    +----+     |  IPv4  +-----+    | IPv6 optional    |  to 6a44 relays)
    |    |-----|        |NAT44|----+                  |
    +----+     |        +-----+    |      +-------------+
     6a44   ---|MTU >= 1308|       |    --+6a44 relay(s)|--- Upstream
   client(s)   |   no      |    ---|      +-------------+  IPv6 network
               |native IPv6|       |                  |
               +-----------+       +------------------+


                             (B) PRIVATE IPv4 ISP NETWORK
                                   +------------------+
                                   |PRIVATE IPv4      |
                                   | as above         |
                                ---|                  |
                                   |     +--------------+
                                   |   --+ ISP NAT44(s) |--- Upstream
                  as above     ----+     +--------------+   IPv4 network
                                   |                  |
                                   |     +--------------+
                                ---|   --+6a44 relay(s) |--- Upstream
                                   |     +--------------+   IPv6 network
                                   |                  |
                                   +------------------+

                  Figure 1: 6a44 Applicability Scenarios









Despres, et al.               Experimental                      [Page 9]
RFC 6751          Native IPv6 behind NAT44 CPEs (6a44)      October 2012


   In both configurations, the ISP network may also assign IPv6 prefixes
   to customer sites:

   o  If customer sites are only assigned IPv4 addresses (IPv6 prefix
      available neither natively nor with any tunnel), 6a44 applies not
      only to sites whose CPEs are IPv4-only capable but also to those
      whose CPEs are dual-stack capable.

   o  If customer sites are assigned both IPv4 addresses and IPv6
      prefixes, 6a44 only applies to sites whose CPEs are IPv4-only
      capable.

   Figure 2 illustrates paths of IPv6 packets between a 6a44 client, A,
   and various possible locations of remote hosts (E in the same site, F
   in another 6a44 site of the same ISP, G in a non-6a44 IPv6 site of
   the same ISP, D in an IPv6 site of another ISP).  Between 6a44
   clients of a same site, IPv6 packets are encapsulated in IPv4
   packets.  Those between 6a44 clients and 6a44 relays are encapsulated
   in UDP/IPv4 packets.

   6a44 operates as follows (details in Section 6):

   1.   A 6a44 client starts operation by sending a 6a44 bubble to the
        6a44-relay UDP/IPv4 address.

   2.   When a 6a44 relay receives a bubble from one of its 6a44
        clients, it returns to this client a bubble containing the IPv6
        prefix of this client.

   3.   When a 6a44 client receives a bubble from a 6a44 relay, it
        updates (or confirms) its 6a44 address.  It is an update if the
        client has no IPv6 address yet or if, due to a CPE reset, this
        address has changed.  After receiving a bubble, a client is
        ready to start, or to continue, IPv6 operation.

   4.   When a 6a44 client having a 6a44 address has an IPv6 packet to
        send whose destination IS in the same customer site, it
        encapsulates it in an IPv4 packet whose destination is found in
        the IPv6 destination address.  It then sends the resulting IPv6/
        IPv4 packet.

   5.   When a 6a44 client receives a valid IPv6/IPv4 packet from a 6a44
        client of the same site, it decapsulates the IPv6 packet and
        submits it to further IPv6 processing.







Despres, et al.               Experimental                     [Page 10]
RFC 6751          Native IPv6 behind NAT44 CPEs (6a44)      October 2012


   6.   When a 6a44 client having a 6a44 address has an IPv6 packet to
        send whose destination IS NOT in the same customer site, it
        encapsulates the packet in a UDP/IPv4 packet whose destination
        is the 6a44-relay UDP/IPv4 address.  It then sends the IPv6/UDP/
        IPv4 packet.

   7.   When a 6a44 relay receives via its IPv4 interface a valid IPv6/
        UDP/IPv4 packet whose destination IS one of its 6a44 clients, it
        forwards the contained IPv6 packet in a modified IPv6/UDP/IPv4
        packet.  The UDP/IPv4 destination of this packet is found in the
        IPv6 destination address.

   8.   When a 6a44 client receives a valid IPv6/UDP/IPv4 packet from a
        6a44 relay, it decapsulates the IPv6 packet and submits it to
        further IPv6 processing.

   9.   When a 6a44 relay receives via its IPv4 interface a valid IPv6/
        UDP/IPv4 packet whose IPv6 destination IS NOT one of its 6a44
        clients, it decapsulates the IPv6 packet and sends it via its
        IPv6 interface.

   10.  When a 6a44 relay receives via its IPv6 interface a valid IPv6
        packet whose destination is one of its 6a44 clients, it
        encapsulates the packet in a UDP/IPv4 packet whose destination
        is the UDP/IPv4 address found in the IPv6 destination address.
        It then sends the resulting IPv6/UDP/IPv4 packet via its IPv4
        interface.

   11.  To maintain the NAT44 mapping of its 6a44 tunnel, and to quickly
        detect the need to change its 6a44 address in case of NAT44
        reset, a 6a44 client from time to time sends a bubble to the
        6a44-relay address (see Section 6.5.1).

   12.  When a 6a44 relay receives via its IPv4 interface an IPv6/UDP/
        IPv4 packet whose IPv6 and UDP/IPv4 source addresses are not
        consistent, it discards the invalid packet and returns a bubble
        to the UDP/IPv4 source address.  (This permits the 6a44 client
        at this address to update its IPv6 address.)













Despres, et al.               Experimental                     [Page 11]
RFC 6751          Native IPv6 behind NAT44 CPEs (6a44)      October 2012


           CUSTOMER         +-------------------------+
             SITES          |      ISP NETWORK        |
          +---------+       +----------------+        |
          |         |       |6a44 ISP NETWORK|        |   GLOBAL
          |         |       |                |        |  INTERNET
   HOSTS  |      IPv6/UDP/IPv4         +---------+    |             HOST
    +-+   |      +-----+    |         B|   6a44  |C/48|     IPv6    +-+
    |A|---|--.---|NAT44|----|----------.---------.----|--- - - - ---|D|
    +-+   |   \  +-----+    |         /| relay(s)|\   |             +-+
    +-+   |   /     |       |        ' +---------+ '  |
    |E|---|--'      |       |        |       |     |  |
    +-+ IPv6/IPv4   |       |        |       |     |  |
          +---------+       |        |       |     |  |
                            |        |       |     |  |
          +---------+       |        |       |     |  |
          |      IPv6/UDP/IPv4       .       |     |  |
    +-+   |      +-----+    |       /        |     |  |
    |F|---|------|NAT44|----|------'         |     |  |
    +-+   |      +-----+    |                |     |  |
          |         |       +----------------+     |  |
          +---------+       |                      .  |
    +-+                     |                     /   |
    |G|---- - - - - - - ----|--------------------'    |
    +-+           IPv6      |                         |
                            +-------------------------+

   IPv6 PATHS A-D:   D is IPv6 of another ISP
              A-E:   E is a 6a44 client in the same site
              A-F:   F is a 6a44 client in another site of the same ISP
              A-G:   G is IPv6 of the same ISP, other than 6a44

         Figure 2: IPv6 Paths between 6a44 Hosts and Remote Hosts

5.  6a44 Addresses

   The 6a44 IPv6 address an ISP assigns to a host must contain all
   pieces of information needed to reach it from other IPv6 addresses.
   These pieces are described below and illustrated in Figure 3:

   o  the 6a44-network IPv6 prefix C (a /48 the ISP has assigned to its
      6a44 relays);

   o  the customer-site IPv4 address N (either global IPv4 or, if the
      ISP uses a [NAT444] model, private IPv4);







Despres, et al.               Experimental                     [Page 12]
RFC 6751          Native IPv6 behind NAT44 CPEs (6a44)      October 2012


   o  the mapped port Z of the 6a44 tunnel (i.e., the external port
      assigned by the NAT44 to the tunnel that the client maintains
      between its UDP/IPv4 local address A:W and the 6a44-relay UDP/IPv4
      address B:W);

   o  the client local IPv4 address A (i.e., the private IPv4 address
      assigned to the client in its customer site; it is needed for
      intra-site IPv6 connectivity).

                  Customer network       ISP network
                  +--------------+       +------------------+
       Client     |IPv4         CPE      |IPv4              |
       +----+     |           +-----+    |        +----------+
       | ^  |-----|           |NAT44|----+        |6a44 relay|---- IPv6
       +-|-^+     |           +-----+    |        +----------+^
         | |      |          ^   |   ^   |         ^        | |
         | |      +----------|---+   |   +---------|--------+ |
         | |                 |   ^   |             |          |
         | |             >0/0|   |   |N/32<        |          |
         | |                     |                 |          |
         | |                  Mapping              |          |
         | |                <a:w>-<N:Z> (*)        |          |
         | |                                       |          |
         | |A:W<                               >B:W|          |
         |                                                    |
    IPv6 |C.N.Z.A/128<                                        |C/48<

    (*) With NAT44(s) between client and CPE, a:w may differ from A:W


    |0                    47|48           79|80   95|96          127|
    +-------+-------+-------+-------+-------+-------+-------+-------+
    |      6a44-network     | Customer-site |Tunnel |  6a44-client  |
    |      IPv6 prefix      |  IPv4 address |mapped |  local IPv4   |
    |          (C)          |      (N)      |port(Z)|  address (A)  |
    +-------+-------+-------+-------+-------+-------+-------+-------+
                                  6a44-client
                            <-- UDP/IPv4 address -->
    <------------ 6a44-client IPv6 prefix --------->
    <---------------- 6a44-client IPv6 address --------------------->

                    Figure 3: Host-Address Construction

   NOTE: 6a44 addresses are not guaranteed to comply with the rule
   listed in [RFC4291], according to which bits 64-127 of aggregatable
   unicast addresses have to be in Modified-EUI-64 Interface Identifier
   (IID) format.  However, these bits within the 6a44 addresses are
   interpreted only where 6a44 addresses are processed, i.e., in 6a44



Despres, et al.               Experimental                     [Page 13]
RFC 6751          Native IPv6 behind NAT44 CPEs (6a44)      October 2012


   relays and clients.  No operational problem is therefore foreseen.
   Besides, because it is a purely transitional tool, it shouldn't
   prevent any "development of future technology that can take advantage
   of interface identifiers with universal scope" (the purpose of this
   format, as expressed in [RFC4291].

6.  Specification of Clients and Relays

6.1.  Packet Formats

6.2.  IPv6 Packet Encapsulations

   For NAT44 traversal, an IPv6 packet transmitted from a 6a44 client to
   a 6a44 relay, or vice versa, is encapsulated in a UDP/IP packet whose
   source and destination addresses are those of the two endpoints (A:W
   and B:W in the notations of Figure 3).  The IPv4 packet is that of a
   complete datagram (its more-fragment bit is set to 0, its offset is
   set to 0, and its datagram identification may be set to 0).  The UDP
   checksum is set to 0 (there is no need for an additional layer of
   checksum protection).  The length of the IPv6 packet SHOULD NOT
   exceed 1280 octets (see Section 6.4).

        Octets: |0         |20 |28                 |68            |
                +----------+---+-------------------+-------//-----+
                |   IPv4   |UDP|    IPv6 header    | IPv6 payload |
                +----------+---+-------------------+-------//-----+

   An IPv6 packet transmitted from a 6a44 client to another 6a44 client
   of the same site is encapsulated in an IPv4 packet whose source and
   destination addresses are the private IPv4 addresses of the two
   hosts.  The IPv4 packet is that of a complete datagram (its
   more-fragment bit is set to 0, its offset is set to 0, and its
   datagram identification may be set to 0).  The size of the IPv6
   packet SHOULD NOT exceed 1280 octets (see Section 6.4).

          Octets:  |0         |20                 |60            |
                   +----------+-------------------+-------//-----+
                   |   IPv4   |    IPv6 header    | IPv6 payload |
                   +----------+-------------------+-------//-----+

6.3.  6a44 Bubbles

   A "bubble" is a UDP/IPv4 packet whose UDP payload is comprised of a
   "6a44-client IPv6 prefix" field and a "Bubble ID" field and whose UDP
   checksum is set to 0.  Having no UDP checksum protection in bubbles
   is a simplification that is acceptable because bubble contents are





Despres, et al.               Experimental                     [Page 14]
RFC 6751          Native IPv6 behind NAT44 CPEs (6a44)      October 2012


   regularly updated and non-critical (a client accepting a corrupted
   IPv6 prefix never leads to any IPv6 packet being accepted by any
   wrong destination).

                      "6a44-client IPv6 prefix" field
         . from a 6a44 client = 0 (also denoted by ::/96)
         . from a 6a44 relay = 6a44-client IPv6 prefix
                                    |
         Octets:  |0         |20 |28| |40 |48
                  +----------+---+--|-+---+
                  |   IPv4   |UDP|  . | . |
                  +----------+---+----+-|-+
                                        |
                                   "Bubble ID" field
          . from a 6a44 client: a client-selected value
          . from a 6a44 relay:
             - in a response bubble, copy of the received Bubble ID
             - in an error-signaling bubble, 0

                       Figure 4: 6a44 Bubble Format

   In a bubble from a 6a44 client to a 6a44 relay, the "6a44-client
   IPv6 prefix" field is only reserved space for the response and is set
   to 0.  In a bubble from a 6a44 relay to a 6a44 client, this field
   contains the IPv6 prefix of the client, left-justified.

   In a bubble from a 6a44 client to a 6a44 relay, the "Bubble ID" field
   contains a randomly chosen value, renewed under the circumstances
   defined in Section 6.5.1.  In a bubble from a 6a44 relay to a 6a44
   client, if the bubble is a response to a bubble received from the
   client, the field contains the value found in the received bubble; if
   the bubble is a reaction to a received IPv6/UDP/IPv4 packet whose
   IPv6 and UDP/IPv4 sources are inconsistent (i.e., not conforming to
   R44-2 condition (3) in Section 6.6.2), the field is set to 0.  The
   purpose of this field is to protect against 6a44-relay spoofing
   attacks (see Section 7).

   In order to preserve forward compatibility with any extension of
   bubble formats -- should one prove useful in the future -- 6a44
   clients and 6a44 relays MUST be configured to receive bubbles whose
   UDP payload lengths are longer than 20 octets (up to that of an IPv6-
   packet header since, as detailed in Sections 6.5.3 and 6.6.2, bubbles
   are recognized by the fact that their lengths are shorter than that
   of tunneled IPv6 packets).







Despres, et al.               Experimental                     [Page 15]
RFC 6751          Native IPv6 behind NAT44 CPEs (6a44)      October 2012


6.4.  MTU Considerations

   Reassembly of a fragmented IPv4 datagram necessitates that its
   identifier be remembered from reception of the first fragment to
   reception of the last one, and necessitates a timeout protection
   against packet losses.  If such stateful IP-layer processing would be
   necessary for 6a44, it would make it more complex than needed, would
   introduce a vulnerability to denial-of-service attacks, and would
   impose the restriction that all fragments of a fragmented IPv4
   datagram go to the same relay.  This last point would be a constraint
   on how load balancing may be performed between multiple 6a44 relays,
   and would therefore be detrimental to scalability.

   For 6a44 processing to remain completely stateless, IPv4 packets
   containing encapsulated IPv6 packets must never be fragmented (DF
   always set to 1).  For this requirement to be met, the following
   apply:

   o  In customer sites, 6a44 clients MUST have IPv4 link MTUs that
      support encapsulated IPv6 packets of lengths up to 1280 octets,
      i.e., for IPv6/UDP/IPv4 packets that traverse the CPE, link MTUs
      of at least 1280+20+8=1308 octets.  (This condition is in general
      satisfied.)

   o  For the same reason, 6a44 ISP networks must have IPv4 path MTUs of
      at least 1308 octets.  (This condition is in general satisfied.)

   o  6a44 clients SHOULD limit the size of IPv6 packets they transmit
      to 1280 octets.

   o  6a44 relays SHOULD set their IPv6 MTU to 1280.  (If a relay
      receives an IPv6 packet longer than this MTU via its IPv6 upstream
      interface, it MUST return an ICMPv6 Packet Too Big error message.)
      Typical ISP networks have path MTUs that would permit IPv6 MTUs of
      6a44 devices to be longer than 1280 octets, but accepting 1280
      octets is a precaution that guarantees against problems with
      customer sites that may have internal path MTUs smaller than those
      supported by their ISP networks.

6.5.  6a44 Client Specification

6.5.1.  Tunnel Maintenance

   For a 6a44-client IPv6 address to remain valid, the port mapping of
   the 6a44 tunnel MUST be maintained in the CPE NAT44.

   For this, the 6a44 client SHOULD apply the equivalent of the
   following TM-x rules, as illustrated in Figure 5.



Despres, et al.               Experimental                     [Page 16]
RFC 6751          Native IPv6 behind NAT44 CPEs (6a44)      October 2012


   TM-1  At initialization, a timer value T1 is randomly chosen in the
         recommended range of 1 to 1.5 seconds, and the "6a44 disabled"
         state is entered.  (Randomness of this value is a precaution to
         avoid the following scenario: if many hosts happened to be
         re-initialized at the same time, the bubble traffic resulting
         from the following rules would be synchronized.)

   TM-2  In the "6a44-disabled" state, if it appears that the interface
         has no IPv6 native address BUT has a private IPv4 address, then
         (1) the Attempt count (a local variable) is set to 1; (2) a new
         Bubble ID (another local variable) is randomly chosen (it is
         not critical how random this new value is, as explained in
         Section 7); (3) a bubble is sent with this Bubble ID; (4) the
         "Bubble sent" state is entered with the timer set to T1.

   TM-3  In the "Bubble sent" state, if the timer expires AND the
         Attempt count is less than 4, then (1) the Attempt count is
         increased by 1; (2) a new bubble is sent with the current
         Bubble ID; (3) the "Bubble sent" state is re-entered with the
         timer reset to T1.

   TM-4  In the "Bubble sent" state, if a bubble is received, then
         (1) the 6a44-client IPv6 address is set to the received
         6a44-client IPv6 prefix followed by the host local IPv4
         address; (2) the "Bubble received" state is entered with the
         timer set to T2, whose recommended value is 30 seconds minus 4
         times T1.

   TM-5  In the "Bubble sent" state, if timer T1 expires AND the Attempt
         count is equal to 4, then the "No 6a44 relay" state is entered
         with the timer set to T3, whose recommended value is 30
         minutes.

   TM-6  In the "Bubble sent" state, OR the "Bubble received" state, OR
         the "No 6a44 relay" state, if an IPv6 native address is
         obtained by some other means, OR if the private IPv4 address of
         the host is no longer valid, then (1) the timer is disarmed;
         (2) the "6a44 disabled" state is entered.

   TM-7  In the "Bubble received" state, if timer T2 expires, then
         (1) the Attempt count is reset to 1; (2) a new Bubble ID is
         randomly chosen; (3) a bubble is sent with this Bubble ID;
         (4) the "Bubble sent" state is entered with the timer set
         to T1.

   TM-8  In the "Bubble received" state, if a bubble is received, then
         the timer is reset to T2.  (NOTE: Since a bubble is received by
         a 6a44 client either in response to a bubble it has sent or in



Despres, et al.               Experimental                     [Page 17]
RFC 6751          Native IPv6 behind NAT44 CPEs (6a44)      October 2012


         reaction to a packet it has sent with inconsistent IPv6 and
         UDP/IPv4 source addresses, receiving a bubble is a sign that
         the tunnel mapping reported in the received bubble prefix has
         recently been used in BOTH directions, a condition required by
         some NAT44s to maintain their mappings.)

   TM-9  In the "No 6a44 relay" state, if the timer expires, then
         (1) the Attempt count is reset to 1; (2) a new Bubble ID is
         randomly chosen; (3) a bubble is sent with this Bubble ID;
         (4) the "Bubble sent" state is entered with the timer set
         to T1.

                        Initialization
                      ________v________
                     /                 \
                     | "6a44 disabled" |------------<-----------------+
                     \_________________/                              ^
                              v no v6-add AND v4-add                  ^
     +--------->--------------v                                       ^
     ^         +--------------v--------------+                        ^
     ^         |   Reset the Attempt count   |                        ^
     ^         |   Renew the Bubble ID       |                        ^
     ^         +--------------+--------------+                        ^
     ^    +----->-------------v                                       ^
     ^    ^    +--------------v--------------+                        ^
     ^    ^    |          Send a bubble      |                        ^
     ^    ^    +--------------v--------------+                        ^
     ^    ^           ________v________                               ^
     ^    ^ Timer T1 /                 \ 4 attempts without answer    ^
     ^    +----<-----|  "Bubble sent"  |-------->----------------+    ^
     ^   (1 to 1.5 s)\_________________/                         v    ^
     ^                        v        \ v6-add OR no v4-add     v    ^
     ^        Bubble received v         +-----------------------------+
     ^                        v-----------------<-----------+    v    ^
     ^               _________v_________                    ^    v    ^
     ^     Timer T2 /                   \Bubble received    ^    v    ^
     +----------<---| "Bubble received" |-------->----------+    v    ^
     ^ (30 s - 4*T1)\___________________/                        v    ^
     ^                                  \ v6-add OR no v4-add    v    ^
     ^                                   +------->--------------------+
     ^                                                           v    ^
     ^                        +----------------------------------+    ^
     ^                 _______v________                               ^
     ^       Timer T3 /                 \ v6-add OR no v4-add         ^
     +-----------<----| "No 6a44 relay" |----->-----------------------+
             (30 min) \_________________/

                  Figure 5: Tunnel Maintenance Algorithm



Despres, et al.               Experimental                     [Page 18]
RFC 6751          Native IPv6 behind NAT44 CPEs (6a44)      October 2012


6.5.2.  Client Transmission

   A 6a44 client transmits packets according to the following CT-x
   rules.  In figures that illustrate these rules, symbols used in
   Section 5 are reused; packets are represented as a succession of
   significant fields separated by commas, with sources preceding
   destinations as usual; != means "different from".

   CT-1  BUBBLE SENT BY A 6a44 CLIENT

               (IPv4, A, B, UDP[W, W, ::/96, <current Bubble ID>])
                                         |
                 +-------+--------+      |
                 |       |  6a44  |      |
                 |       | client +------>---------- >B:W
                 |       |function|A:W<     UDP/IPv4
                 +-------+--------+
                        Host

   Bubbles are transmitted from time to time.  Conditions of their
   transmission are specified in Section 6.5.1, and their format is
   specified in Section 6.3.

   CT-2  IPv6/IPv4 PACKET SENT TO A HOST OF THE SAME SITE

            [IPv6, <C.N.Z.A>, <C.N..E>,...]
                  |
                  | (IPv4, A, A2, IP-in-IP[encapsulated packet])
                  |                  |
             +----|--+--------+      |
             |    |  |  6a44  |      |
             |  -->--+ client +------>------ >A2
             |  IPv6 |function|<A       IPv4
             +-------+--------+
                     Host

   If an IPv6 packet is submitted for transmission with ALL the
   following conditions satisfied, the 6a44 client MUST encapsulate the
   IPv6 packet in an IPv4 packet whose protocol is set to IP in IP
   (protocol = 41) and whose IPv4 destination is copied from the last 32
   bits of the IPv6 destination: (1) the IPv6 source address is the
   6a44-client IPv6 address; (2) the IPv6 destination is a 6a44 address
   of the same site (it has the same 80 bits as the 6a44-client IPv6
   address); (3) either the IPv6 packet does not exceed 1280 octets, or
   it is longer but it does not exceed the IPv4 link MTU minus 20 octets
   and the IPv4 destination address starts with the IPv4 link prefix.





Despres, et al.               Experimental                     [Page 19]
RFC 6751          Native IPv6 behind NAT44 CPEs (6a44)      October 2012


   CT-3  IPv6/UDP/IPv4 PACKET TO A HOST OF ANOTHER SITE

           [IPv6, <C.N.Z.A>, X != <C.N...>, ...]
                 |
                 | (IPv4, B, A, UDP(W, W, [encapsulated packet])
                 |                  |
            +----|--+--------+      |
            |    |  |  6a44  |      |
            |  -->--+ client +------>---------- >B:W
            |  IPv6 |function|A:W<     UDP/IPv4
            +-------+--------+
                    Host

   If an IPv6 packet is submitted for transmission and ALL the following
   conditions are satisfied, the IPv6 packet MUST be encapsulated in a
   UDP/IPv4 packet whose destination is the 6a44-relay anycast address
   and whose source and destination ports are both the 6a44 port:
   (1) the source address is the local 6a44-client IPv6 address; (2) the
   destination is not a 6a44 address of the same site (its first 80 bits
   differ from those of the 6a44-client IPv6 address); (3) the IPv6
   packet does not exceed 1280 octets.

   CT-4  IPv6 PACKET THAT DOESN'T CONCERN 6a44

         If an IPv6 packet is submitted to the 6a44 client function for
         transmission with an IPv6 source address that is not the
         6a44-client IPv6 address, the packet does not concern 6a44.  It
         MUST be left for any other IPv6 transmission function that may
         apply (the source address can be a link-local address or a
         Unique Local Address (ULA) [RFC4193]).

6.5.3.  Client Reception

   Upon reception of an IPv4 packet, a 6a44 client applies the following
   CR-x rules:

   CR-1  BUBBLE RECEIVED FROM A 6a44 RELAY

                (IPv4, B, A, UDP(W, W, [<C.N.Z>, <current Bubble ID>])
                                    |
            +-------+--------+      |
            |       |  6a44  |      |
            |       | client +------<---------- <B:W
            |       |        |A:W<     UDP/IPv4
            +-------+--------+
                   Host
              (updates C.N.Z)




Despres, et al.               Experimental                     [Page 20]
RFC 6751          Native IPv6 behind NAT44 CPEs (6a44)      October 2012


   If ALL the following conditions are satisfied (i.e., the packet is a
   6a44 bubble from a 6a44 relay), the 6a44-client IPv6 address MUST be
   updated using the received IPv6 prefix C.N.Z: (1) the IPv4 packet
   contains a complete UDP datagram (protocol = 17, offset = 0,
   more-fragment bit = 0); (2) both ports of the UDP datagram are the
   6a44 port, and the payload length is enough to contain a 6a44-client
   IPv6 prefix and a Bubble ID but shorter than an IPv6-packet header
   (protocol = 17, UDP payload length = at least 20 octets and less than
   40 octets); (3) the received Bubble ID matches the current value of
   the Bubble-ID local variable.

   CR-2  IPv6/IPv4 PACKET FROM A HOST OF THE SAME SITE

             (IPv4, E, A, IP-in-IP, [IPv6, <C.N..A2>, <C.N.Z.A>, ...])
                                  |
         [decapsulated packet]    |
               |                  |
          +----|--+--------+      |
          |    |  |  6a44  |      |
          |  --<--+ client +------<------ <A2
          |  IPv6 |        |A<       IPv4
          +-------+--------+
                  Host

   If ALL the following conditions are satisfied (i.e., the packet comes
   from a 6a44 client of the same site), the 6a44 client MUST
   decapsulate the inner packet and treat it as a received IPv6 packet:
   (1) the IPv4 packet contains a complete UDP datagram (protocol = 17,
   offset = 0, more-fragment bit = 0); (2) both ports of the UDP
   datagram are the 6a44 port, and the UDP payload is an IPv6 packet
   (UDP length of at least 40 octets, version = 6); (3) the IPv6 source
   address is one of the same site (the first 80 bits match those of the
   6a44-client IPv6 address; (4) its last 32 bits are equal to the IPv4
   source address; (5) the IPv6 destination address is the 6a44-client
   IPv6 address.

   CR-3  IPv6/UDP/IPv4 PACKET FROM A HOST OF ANOTHER SITE

                    (IPv4, B, A, UDP(W, W, [IPv6, X, <C.N.Z.A>,...])
                                       |
              [decapsulated packet]    |
                    |                  |
               +----|--+--------+      |
               |    |  |  6a44  |      |
               |  --<--+ client +------<---------- <B:W
               |  IPv6 |        |A:W<     UDP/IPv4
               +-------+--------+
                       Host



Despres, et al.               Experimental                     [Page 21]
RFC 6751          Native IPv6 behind NAT44 CPEs (6a44)      October 2012


   If ALL the following conditions are satisfied (i.e., the packet has
   been relayed by a 6a44 relay), the 6a44 client MUST decapsulate the
   inner packet and treat it as a received IPv6 packet: (1) the IPv4
   packet contains a complete UDP datagram (protocol = 17, offset = 0,
   more-fragment bit = 0); (2) the UDP payload is an IPv6 packet (length
   of at least 40 octets, version = 6); (3) the UDP/IPv4 source address
   is the 6a44-relay UDP/IPv4 address; (4) the IPv6 destination address
   is the 6a44-client IPv6 address.

   CR-4  RECEIVED ICMPv4 ERROR MESSAGE CONCERNING A 6a44 PACKET

         If the 6a44 client receives an IPv4 error message [RFC0792]
         that concerns a discarded 6a44 packet (i.e., if the copied
         header of the discarded packet is that of a transmitted packet
         according to CT-2 or CT-3), it SHOULD translate it into an
         ICMPv6 error message [RFC4443] and then treat it as a received
         IPv6 packet.  Translation of Type and Code conversions between
         IPv4 and IPv6 is described in Section 4.2 of [RFC6145], under
         "ICMPv4 error messages".

   CR-5  RECEIVED IPv4 PACKET OTHER THAN 6a44

         If ANY one or more of the following conditions are verified,
         the received IPv4 packet does not concern 6a44 and MUST
         therefore be left for any other IPv4 reception function that
         may apply: (1) the IPv4 payload is neither UDP nor IPv6
         (protocol = neither 17 nor 41, or protocol = 41 and IP version
         in the payload is not = 6); (2) the IPv4 packet is an
         IP-datagram fragment other than the first one (offset > 0);
         (3) the IPv4 packet contains the first or unique fragment of a
         UDP datagram (protocol = 17, offset = 0), with neither port
         equal to the 6a44 port.



















Despres, et al.               Experimental                     [Page 22]
RFC 6751          Native IPv6 behind NAT44 CPEs (6a44)      October 2012


6.6.  6a44 Relay Specification

6.6.1.  Relay Reception in IPv6

   Upon reception of a packet via its IPv6 interface with a destination
   address starting with the 6a44-network IPv6 prefix, a 6a44 relay MUST
   apply the following RR6-x rules:

   RR6-1  VALID IPv6 PACKET FROM OUTSIDE THE 6a44 ISP NETWORK

    [IPv6, (X != <C...> AND != <Teredo(IPv4=B)>), <C.<N != B>.Z...>,...]
                                      |
    (IPv4, B, N, UDP(W, Z,            |
          [encapsulated packet]))     |
            |                         |
            |        +--------+       |
            |   >B:W |  6a44  |C/48<  |
    N:Z< ---<--------| relay  |-------<---- C.N.Z...<
         IPv4        |        |        IPv6
                     +--------+

   If ALL the following conditions are satisfied, the IPv6 packet MUST
   be encapsulated in a UDP/IPv4 packet whose UDP/IPv4 destination is
   copied from bits 48 to 95 of the IPv6 destination address: (1) the
   IPv6 source address is not that of a 6a44 client of the ISP (it does
   not start with the 6a44-network IPv6 prefix); (2) the IPv6 source
   address is not a Teredo address whose embedded UDP/IPv4 address is
   the 6a44-relay anycast address; (3) the customer-site IPv4 address
   embedded in the 6a44 destination address is not the 6a44-relay
   anycast address; (4) the packet has at most 1280 octets.

   RR6-2  INVALID IPv6 PACKET FROM OUTSIDE THE 6a44 ISP NETWORK

          If ANY one or more of the following conditions are satisfied,
          the IPv6 packet MUST be discarded: (1) the packet has more
          than 1280 octets (in this case, an ICMPv6 Packet Too Big error
          message MUST be returned to the source); (2) the customer-site
          IPv4 address embedded in the IPv6 destination address is the
          6a44-relay anycast address; (3) the IPv6 source address is a
          Teredo address whose embedded IPv4 address is the 6a44-relay
          anycast address.










Despres, et al.               Experimental                     [Page 23]
RFC 6751          Native IPv6 behind NAT44 CPEs (6a44)      October 2012


6.6.2.  Relay Reception in IPv4

   Upon reception via its IPv4 downstream interface of an IPv4 packet
   that contains a complete IP datagram (fragment offset = 0 and
   more-fragment bit = 0) and that contains a UDP datagram whose UDP/
   IPv4 destination is the 6a44-relay UDP/IPv4 address, a 6a44 relay
   MUST apply the following rules:

   RR4-1  BUBBLE FROM 6a44 CLIENT

               (IPv4, N, B, UDP(Z, W, [::/96, Bubble ID]))
                                     |
                              IPv4   |    +--------+
                              ------->----|        |
                                      >B:W|  6a44  |
                                          |  relay |
                         N:Z< -------<----|        |
                              IPv4   |    +--------+
                                     |
                                     |
                (IPv4, B, N, UDP(W, Z, [<C.N.Z>, Bubble ID]))

   If the following condition is satisfied, the 6a44 relay MUST return
   to the source a bubble derived from the bubble it just received by
   permuting its UDP/IPv4 source and destination, and by putting in its
   6a44-client-IPv6-prefix field the received UDP/IPv4 source address:
   the UDP payload is a bubble, i.e., has at least 20 octets and less
   than 40 octets.

   RR4-2  IPv6 PACKET FROM A 6a44 CLIENT TO ANOTHER 6a44 CLIENT

     (IPv4, N1, B, UDP(Z1, W, [IPv6, <C.N1.Z1...>, <C.N2.Z2...>, ...]))
                   |
            IPv4   |    +--------+
            ------->----|        |
                    >B:W|  6a44  |
                        | relay  |
                        |        |
     N2.Z2< -------<----|        |
            IPv4   |    +--------+
                   |        6a44 relay
                   |
     (IPv4, B, N2, UDP(W, Z2, [encapsulated packet]))

   If ALL the following conditions are satisfied, the 6a44 relay MUST
   return back via its downstream IPv4 interface an IPv6/ UDP/IPv4
   packet containing the same encapsulated packet, having its UDP/IPv4
   destination set to the UDP/IPv4 address found in the 6a44 destination



Despres, et al.               Experimental                     [Page 24]
RFC 6751          Native IPv6 behind NAT44 CPEs (6a44)      October 2012


   address, and having its UDP/IPv4 source set to the 6a44-relay
   UDP/IPv4 address: (1) the IPv4 packet contains a complete UDP
   datagram (protocol = 17, offset = 0, more-fragment bit = 0); (2) the
   UDP payload is an IPv6 packet (length of at least 40 octets, version
   = 6); (3) the IPv6 source address starts with the 6a44-network IPv6
   prefix followed by the UDP/IPv4 source address of the received
   packet; (4) the IPv6 destination address starts with the 6a44-network
   IPv6 prefix.

   RR4-3  IPv6 PACKET FROM A 6a44 CLIENT TO A NON-6a44 CLIENT

        (IPv4, N, B, UDP(Z, W, [IPv6, <C.N.Z...>,
                  |    (X != <C...> AND != <Teredo(IPv4=B)), ...]))
                  |
                  |                      [decapsulated packet]
                  |                           |
                  |          +--------+       |
                  |      B:W>|  6a44  |       |
         >B:W  --->----------| relay  |------->---- >
               IPv4          |        |        IPv6
                             +--------+

   If ALL the following conditions are satisfied, the 6a44 relay MUST
   decapsulate the IPv6 packet and forward it via the IPv6 interface:
   (1) the IPv4 packet contains a complete UDP datagram (protocol = 17,
   offset = 0, more-fragment bit = 0); (2) the UDP payload is an IPv6
   packet (length of at least 40 octets, version = 6); (3) the IPv6
   source address starts with the 6a44-network IPv6 prefix followed by
   the UDP/IPv4 source address of the received packet; (4) the IPv6
   destination address does not start with the 6a44-network IPv6 prefix
   and is not a Teredo address whose embedded IPv4 address is the
   6a44-relay anycast address.

   RR4-4  RECEIVED ICMPv4 ERROR MESSAGE CONCERNING A 6a44 PACKET

          If the 6a44 relay receives an IPv4 error message [RFC0792]
          that concerns a discarded 6a44 packet (i.e., if the copied
          header of the discarded packet is that of a transmitted packet
          according to RR6-1 or RR4-2), it SHOULD translate it into an
          ICMPv6 error message [RFC4443] and then treat it as a received
          IPv6 packet.  Translation of Type and Code conversions between
          IPv4 and IPv6 is described in Section 4.2 of [RFC6145], under
          "ICMPv4 error messages".

   RR4-5  INVALID IPv6/UDP/IPv4 PACKET

          For ANY other case, the 6a44 relay MUST discard the packet.




Despres, et al.               Experimental                     [Page 25]
RFC 6751          Native IPv6 behind NAT44 CPEs (6a44)      October 2012


6.7.  Implementation of Automatic Sunset

   6a44 is designed as an interim transition mechanism, not to be used
   any longer than strictly necessary.  Its sole purpose is to
   accelerate availability of IPv6 native addresses where, for any
   reason, CPEs cannot quickly be replaced, or where, for any reason,
   ISP networks cannot quickly support dual-stack routing or 6rd.

   A 6a44-capable ISP can first have an increase in its 6a44 traffic as
   more and more hosts behind IPv4-only CPEs support the 6a44 client
   function, but it should later have a decrease in this traffic as more
   and more CPEs operate in dual stack.

   When this traffic becomes sufficiently negligible, the ISP may, after
   due prior notice, discontinue 6a44-relay operation.  This terminates
   its sunset procedure.

   In a host that obtains an IPv6 native address by some means other
   than 6a44, the effect of having the 6a44 function in its protocol
   stack is inexistent.  OS providers may therefore keep this function
   in their code for many years.  When it becomes clear that the number
   of users of this function has become negligible, they can delete it
   from later releases.  This terminates their sunset procedure.

7.  Security Considerations

   Incoming reachability:

      Hosts that acquire 6a44 addresses become reachable from the
      Internet in IPv6 while they remain unreachable in IPv4 at their
      private IPv4 addresses.

      For ordinary use, this should not introduce a perceptible new
      security risk for two reasons: (1) hosts can, without IPv6, use
      NAT44 hole-punching techniques such as Interactive Connectivity
      Establishment (ICE) [RFC5245] to receive incoming connections;
      (2) by default, modern operating systems that support IPv6 have
      their own protections against incoming connections.

      If 6a44 reachability across an ordinary NAT44 nevertheless has to
      be barred, this can be done by configuring its port-forwarding
      function with the 6a44 port bound to any internal address that is
      not assigned to any host.  Thus, no bubble from a 6a44 relay can
      reach any 6a44-capable host, and this is sufficient to prevent
      hosts from using 6a44.






Despres, et al.               Experimental                     [Page 26]
RFC 6751          Native IPv6 behind NAT44 CPEs (6a44)      October 2012


      For more sophisticated uses with managed firewalls, default
      configurations generally specify that packets that are not
      explicitly authorized are discarded.  Thus, 6a44 can be used only
      if the 6a44 port is deliberately opened to incoming traffic.

   Subscriber authentication:

      Any authentication that applies to an IPv4 address extends its
      effect to 6a44 addresses that are derived from it.

   Host-address spoofing:

      With ingress filtering required in 6a44 ISP networks, and with the
      address checks specified in Section 6, no new IPv6 address-
      spoofing vulnerability is introduced by 6a44.

   Address-and-port scanning:

      To mitigate the (limited) risk of a malicious user trying to scan
      IPv4 address/port pairs to reach a host, Teredo addresses contain
      12 random bits [RFC5991].  6a44 addresses have no random bits but
      contain local IPv4 addresses of clients.  Since possible values of
      these addresses are not deterministically known from outside
      customer sites and are in ranges that can be configured in typical
      NAT44s, some protection against address and port scanning is thus
      achieved.  This protection may be less effective than that
      achieved with random bits but is in any case better for 6a44 IPv6
      addresses than for IPv4 addresses alone.

   Denial of service:

      Provided 6a44 relays are provisioned with enough processing power,
      which is facilitated by their being completely stateless, 6a44
      introduces no denial-of-service vulnerabilities of its own.

















Despres, et al.               Experimental                     [Page 27]
RFC 6751          Native IPv6 behind NAT44 CPEs (6a44)      October 2012


   Routing loops:

      A risk of routing-loop attacks has been identified in [RFC6324].
      Without taking precautions, it applies to some combinations of
      automatic-tunnel mechanisms such as 6to4, the Intra-Site Automatic
      Tunnel Addressing Protocol (ISATAP), 6rd, and Teredo.  This risk
      does not exist with 6a44 for the following reasons:

      1.  When a packet enters a 6a44 relay via its IPv6 interface, the
          following apply:

          +  An IPv6/UDP/IPv4 packet cannot be sent to another 6a44
             relay because its IPv4 destination would have to be a
             6a44-relay IPv4 address.  This is prevented by rule RR6-1
             of Section 6.6.1.

          +  If an IPv6/UDP/IPv4 packet is sent to the address of a 6to4
             relay, 6rd relay, or ISATAP relay, it will be discarded
             there because these relays don't accept UDP/IPv4 packets.

          +  If an IPv6/UDP/IPv4 packet is sent to a Teredo relay, it
             will be discarded there because (1) Teredo relays check
             that the IPv4 address that is embedded in the IPv6 source
             address of a received IPv6/IPv4 packet matches the IPv4
             source address of the encapsulating packet (Section 5.4.2
             of [RFC4380]); (2) encapsulating packets sent by 6a44
             relays have the 6a44-relay anycast address as the IPv4
             source address; (3) a 6a44 relay forwards a received IPv6
             packet as an IPv6/UDP/IPv4 packet only if its IPv6 source
             address is not a Teredo address whose embedded IPv4 address
             is the 6a44-relay IPv4 address.

      2.  When a packet enters a 6a44 relay via its IPv4 interface, the
          following apply:

          +  The received packet cannot come from another 6a44 relay (as
             just explained, 6rd relays do not send IPv6/UDP/IPv4
             packets to other 6a44 relays).

          +  If the IPv4 packet comes from a 6to4 relay, a 6rd relay, or
             an ISATAP relay, its IPv6 encapsulated packet cannot be
             forwarded (the received packet is IPv6/IPv4 instead of
             being IPv6/UDP/IPv4, as required by rules RR4-2 and RR4-3
             of Section 6.6.2).

          +  If the received packet is an IPv6/UDP/IPv4 packet coming
             from a Teredo relay, this packet cannot have been sent to
             the Teredo relay by a 6a44 relay: (1) in order to reach the



Despres, et al.               Experimental                     [Page 28]
RFC 6751          Native IPv6 behind NAT44 CPEs (6a44)      October 2012


             6a44 relay, the IPv6 destination of the IPv6 encapsulated
             packet must be a Teredo address whose embedded IPv4 address
             is the 6a44-relay anycast address (Section 5.4.1 of
             [RFC4380]); (2) a 6a44 relay does not forward via its IPv6
             interface an IPv6 packet whose destination is a Teredo
             address whose embedded IPv4 address is the 6a44-relay
             anycast address (rule RR4-3 of Section 6.6.2).

   6a44-relay spoofing:

      In a 6a44 network, no node can spoof a 6a44 relay because ingress
      filtering prevents any 6a44-relay anycast address from being
      spoofed.

      In a network that does not support ingress filtering (and
      therefore is not a 6a44 network), the following apply:

      *  6a44 packets sent by 6a44-capable hosts are discarded in the
         IPv4 backbone because their IPv4 destination, the 6a44-relay
         anycast address, does not start with any ISP-assigned prefix.

      *  If an attacker tries to send to a 6a44-capable host a fake
         relay-to-client bubble, the probability that it would be
         accepted by its destination is negligible.  It would require
         that all the following conditions be simultaneously satisfied:

         +  The UDP/IPv4 destination set by the attacker must reach a
            NAT44 node in which it is the external mapping of a 6a44
            tunnel established by a 6a44-capable host.

         +  This host must be in the "Bubble sent" state -- the only one
            in which it listens to bubbles when its ISP is not 6a44
            capable.  This state is taken only for a few seconds every
            30 minutes (rule TM-5 of Section 6.5.1).

         +  This host accepts the bubble only if its Bubble ID has the
            right value -- an extremely unlikely possibility with a
            64-bit randomly chosen Bubble ID (see Section 6.5.1).

      *  If a 6a44-capable host -- despite this scenario being very
         unlikely -- accepts a fake bubble, the effect is that it
         wrongly believes, for about 30 seconds, that it has an assigned
         public IPv6 address.  All IPv6 packets it then sends with this
         address as the source cannot be accepted by any destination (no
         relay will forward them, and no host of the same site will
         accept them).  The consequences of this scenario would
         therefore not impair security.




Despres, et al.               Experimental                     [Page 29]
RFC 6751          Native IPv6 behind NAT44 CPEs (6a44)      October 2012


8.  IANA Considerations

   IANA has assigned the following:

   1.  IPv4 address 192.88.99.2 as the 6a44-relay anycast address (B in
       this document).

   2.  UDP port 1027 as the 6a44 port (W in this document).

   The choice of 192.88.99.2 as the 6a44 IPv4 anycast address doesn't
   conflict with any existing IETF specification because

   o  it starts with the 6to4 prefix 192.88.99.0/24 [RFC3068].

   o  it differs from the only currently assigned address that starts
      with this prefix (the anycast address of 6to4 relays --
      192.88.99.1 [RFC3068].

   This choice is made to permit implementations of 6a44 relays in
   physical nodes that are independent from any 6to4 relay or, if found
   to be more optimum, in nodes in which 6to4 relays and 6a44 relays are
   collocated.

9.  Acknowledgments

   This specification, whose origin is a convergence effort based on two
   independent proposals -- [6rd+] and [SAMPLE] -- has benefited from
   various suggestions.  Comments have been received during this
   process, in particular from Dave Thaler, Fred Templin, Ole Troan,
   Olivier Vautrin, Pascal Thubert, Washam Fan, and Yu Lee.  The authors
   wish to thank them, and all others, for their useful contributions.
   Special recognition is due to Dave Thaler and John Mann.  Their
   detailed reviews led to a few useful modifications and editorial
   improvements.

10.  References

10.1.  Normative References

   [RFC0792]  Postel, J., "Internet Control Message Protocol", STD 5,
              RFC 792, September 1981.

   [RFC2119]  Bradner, S., "Key words for use in RFCs to Indicate
              Requirement Levels", BCP 14, RFC 2119, March 1997.







Despres, et al.               Experimental                     [Page 30]
RFC 6751          Native IPv6 behind NAT44 CPEs (6a44)      October 2012


   [RFC2460]  Deering, S. and R. Hinden, "Internet Protocol, Version 6
              (IPv6) Specification", RFC 2460, December 1998.

   [RFC4291]  Hinden, R. and S. Deering, "IP Version 6 Addressing
              Architecture", RFC 4291, February 2006.

10.2.  Informative References

   [6rd+]     Despres, R., "Rapid Deployment of Native IPv6 Behind IPv4
              NATs (6rd+)", Work in Progress, July 2010.

   [NAT444]   Yamaguchi, J., Shirasaki, Y., Miyakawa, S., Nakagawa, A.,
              and H. Ashida, "NAT444 addressing models", Work
              in Progress, July 2012.

   [RFC1918]  Rekhter, Y., Moskowitz, B., Karrenberg, D., de Groot, G.,
              and E. Lear, "Address Allocation for Private Internets",
              BCP 5, RFC 1918, February 1996.

   [RFC2827]  Ferguson, P. and D. Senie, "Network Ingress Filtering:
              Defeating Denial of Service Attacks which employ IP Source
              Address Spoofing", BCP 38, RFC 2827, May 2000.

   [RFC3053]  Durand, A., Fasano, P., Guardini, I., and D. Lento, "IPv6
              Tunnel Broker", RFC 3053, January 2001.

   [RFC3056]  Carpenter, B. and K. Moore, "Connection of IPv6 Domains
              via IPv4 Clouds", RFC 3056, February 2001.

   [RFC3068]  Huitema, C., "An Anycast Prefix for 6to4 Relay Routers",
              RFC 3068, June 2001.

   [RFC3704]  Baker, F. and P. Savola, "Ingress Filtering for Multihomed
              Networks", BCP 84, RFC 3704, March 2004.

   [RFC4193]  Hinden, R. and B. Haberman, "Unique Local IPv6 Unicast
              Addresses", RFC 4193, October 2005.

   [RFC4380]  Huitema, C., "Teredo: Tunneling IPv6 over UDP through
              Network Address Translations (NATs)", RFC 4380,
              February 2006.

   [RFC4443]  Conta, A., Deering, S., and M. Gupta, Ed., "Internet
              Control Message Protocol (ICMPv6) for the Internet
              Protocol Version 6 (IPv6) Specification", RFC 4443,
              March 2006.





Despres, et al.               Experimental                     [Page 31]
RFC 6751          Native IPv6 behind NAT44 CPEs (6a44)      October 2012


   [RFC5245]  Rosenberg, J., "Interactive Connectivity Establishment
              (ICE): A Protocol for Network Address Translator (NAT)
              Traversal for Offer/Answer Protocols", RFC 5245,
              April 2010.

   [RFC5569]  Despres, R., "IPv6 Rapid Deployment on IPv4
              Infrastructures (6rd)", RFC 5569, January 2010.

   [RFC5626]  Jennings, C., Ed., Mahy, R., Ed., and F. Audet, Ed.,
              "Managing Client-Initiated Connections in the Session
              Initiation Protocol (SIP)", RFC 5626, October 2009.

   [RFC5969]  Townsley, W. and O. Troan, "IPv6 Rapid Deployment on IPv4
              Infrastructures (6rd) -- Protocol Specification",
              RFC 5969, August 2010.

   [RFC5991]  Thaler, D., Krishnan, S., and J. Hoagland, "Teredo
              Security Updates", RFC 5991, September 2010.

   [RFC6081]  Thaler, D., "Teredo Extensions", RFC 6081, January 2011.

   [RFC6145]  Li, X., Bao, C., and F. Baker, "IP/ICMP Translation
              Algorithm", RFC 6145, April 2011.

   [RFC6324]  Nakibly, G. and F. Templin, "Routing Loop Attack Using
              IPv6 Automatic Tunnels: Problem Statement and Proposed
              Mitigations", RFC 6324, August 2011.

   [SAMPLE]   Carpenter, B. and S. Jiang, "Legacy NAT Traversal for
              IPv6: Simple Address Mapping for Premises Legacy Equipment
              (SAMPLE)", Work in Progress, June 2010.

   [TheTool]  de Saint-Exupery, A., "Wind, Sand and Stars", Chapter III
              (The Tool), 1939.

















Despres, et al.               Experimental                     [Page 32]
RFC 6751          Native IPv6 behind NAT44 CPEs (6a44)      October 2012


Authors' Addresses

   Remi Despres (editor)
   RD-IPtech
   3 rue du President Wilson
   Levallois
   France

   EMail: despres.remi@laposte.net


   Brian Carpenter
   University of Auckland
   Department of Computer Science
   PB 92019
   Auckland  1142
   New Zealand

   EMail: brian.e.carpenter@gmail.com


   Dan Wing
   Cisco Systems, Inc.
   170 West Tasman Drive
   San Jose, California  95134
   USA

   EMail: dwing@cisco.com


   Sheng Jiang
   Huawei Technologies Co., Ltd.
   Q14, Huawei Campus - No. 156 Beiqing Road
   Hai-Dian District, Beijing  100095
   P.R. China

   EMail: jiangsheng@huawei.com














Despres, et al.               Experimental                     [Page 33]
  1. RFC 6751