Home

RFC6126

  1. RFC 6126
Independent Submission                                     J. Chroboczek
Request for Comments: 6126                    PPS, University of Paris 7
Category: Experimental                                        April 2011
ISSN: 2070-1721


                       The Babel Routing Protocol

Abstract

   Babel is a loop-avoiding distance-vector routing protocol that is
   robust and efficient both in ordinary wired networks and in wireless
   mesh networks.

Status of This Memo

   This document is not an Internet Standards Track specification; it is
   published for examination, experimental implementation, and
   evaluation.

   This document defines an Experimental Protocol for the Internet
   community.  This is a contribution to the RFC Series, independently
   of any other RFC stream.  The RFC Editor has chosen to publish this
   document at its discretion and makes no statement about its value for
   implementation or deployment.  Documents approved for publication by
   the RFC Editor are not a candidate for any level of Internet
   Standard; see Section 2 of RFC 5741.

   Information about the current status of this document, any errata,
   and how to provide feedback on it may be obtained at
   http://www.rfc-editor.org/info/rfc6126.

Copyright Notice

   Copyright (c) 2011 IETF Trust and the persons identified as the
   document authors.  All rights reserved.

   This document is subject to BCP 78 and the IETF Trust's Legal
   Provisions Relating to IETF Documents
   (http://trustee.ietf.org/license-info) in effect on the date of
   publication of this document.  Please review these documents
   carefully, as they describe your rights and restrictions with respect
   to this document.








Chroboczek                    Experimental                      [Page 1]
RFC 6126               The Babel Routing Protocol             April 2011


Table of Contents

   1.  Introduction . . . . . . . . . . . . . . . . . . . . . . . . .  3
     1.1.  Features . . . . . . . . . . . . . . . . . . . . . . . . .  3
     1.2.  Limitations  . . . . . . . . . . . . . . . . . . . . . . .  4
     1.3.  Specification of Requirements  . . . . . . . . . . . . . .  4
   2.  Conceptual Description of the Protocol . . . . . . . . . . . .  4
     2.1.  Costs, Metrics, and Neighbourship  . . . . . . . . . . . .  5
     2.2.  The Bellman-Ford Algorithm . . . . . . . . . . . . . . . .  5
     2.3.  Transient Loops in Bellman-Ford  . . . . . . . . . . . . .  6
     2.4.  Feasibility Conditions . . . . . . . . . . . . . . . . . .  6
     2.5.  Solving Starvation: Sequencing Routes  . . . . . . . . . .  8
     2.6.  Requests . . . . . . . . . . . . . . . . . . . . . . . . .  9
     2.7.  Multiple Routers . . . . . . . . . . . . . . . . . . . . . 10
     2.8.  Overlapping Prefixes . . . . . . . . . . . . . . . . . . . 11
   3.  Protocol Operation . . . . . . . . . . . . . . . . . . . . . . 11
     3.1.  Message Transmission and Reception . . . . . . . . . . . . 11
     3.2.  Data Structures  . . . . . . . . . . . . . . . . . . . . . 12
     3.3.  Acknowledged Packets . . . . . . . . . . . . . . . . . . . 15
     3.4.  Neighbour Acquisition  . . . . . . . . . . . . . . . . . . 15
     3.5.  Routing Table Maintenance  . . . . . . . . . . . . . . . . 17
     3.6.  Route Selection  . . . . . . . . . . . . . . . . . . . . . 21
     3.7.  Sending Updates  . . . . . . . . . . . . . . . . . . . . . 22
     3.8.  Explicit Route Requests  . . . . . . . . . . . . . . . . . 24
   4.  Protocol Encoding  . . . . . . . . . . . . . . . . . . . . . . 27
     4.1.  Data Types . . . . . . . . . . . . . . . . . . . . . . . . 28
     4.2.  Packet Format  . . . . . . . . . . . . . . . . . . . . . . 29
     4.3.  TLV Format . . . . . . . . . . . . . . . . . . . . . . . . 29
     4.4.  Details of Specific TLVs . . . . . . . . . . . . . . . . . 30
   5.  IANA Considerations  . . . . . . . . . . . . . . . . . . . . . 39
   6.  Security Considerations  . . . . . . . . . . . . . . . . . . . 39
   7.  References . . . . . . . . . . . . . . . . . . . . . . . . . . 40
     7.1.  Normative References . . . . . . . . . . . . . . . . . . . 40
     7.2.  Informative References . . . . . . . . . . . . . . . . . . 40
   Appendix A.  Cost and Metric Computation . . . . . . . . . . . . . 41
     A.1.  Maintaining Hello History  . . . . . . . . . . . . . . . . 41
     A.2.  Cost Computation . . . . . . . . . . . . . . . . . . . . . 42
     A.3.  Metric Computation . . . . . . . . . . . . . . . . . . . . 43
   Appendix B.  Constants . . . . . . . . . . . . . . . . . . . . . . 43
   Appendix C.  Simplified Implementations  . . . . . . . . . . . . . 44
   Appendix D.  Software Availability . . . . . . . . . . . . . . . . 45










Chroboczek                    Experimental                      [Page 2]
RFC 6126               The Babel Routing Protocol             April 2011


1.  Introduction

   Babel is a loop-avoiding distance-vector routing protocol that is
   designed to be robust and efficient both in networks using prefix-
   based routing and in networks using flat routing ("mesh networks"),
   and both in relatively stable wired networks and in highly dynamic
   wireless networks.

1.1.  Features

   The main property that makes Babel suitable for unstable networks is
   that, unlike naive distance-vector routing protocols [RIP], it
   strongly limits the frequency and duration of routing pathologies
   such as routing loops and black-holes during reconvergence.  Even
   after a mobility event is detected, a Babel network usually remains
   loop-free.  Babel then quickly reconverges to a configuration that
   preserves the loop-freedom and connectedness of the network, but is
   not necessarily optimal; in many cases, this operation requires no
   packet exchanges at all.  Babel then slowly converges, in a time on
   the scale of minutes, to an optimal configuration.  This is achieved
   by using sequenced routes, a technique pioneered by Destination-
   Sequenced Distance-Vector routing [DSDV].

   More precisely, Babel has the following properties:

   o  when every prefix is originated by at most one router, Babel never
      suffers from routing loops;

   o  when a prefix is originated by multiple routers, Babel may
      occasionally create a transient routing loop for this particular
      prefix; this loop disappears in a time proportional to its
      diameter, and never again (up to an arbitrary garbage-collection
      (GC) time) will the routers involved participate in a routing loop
      for the same prefix;

   o  assuming reasonable packet loss rates, any routing black-holes
      that may appear after a mobility event are corrected in a time at
      most proportional to the network's diameter.

   Babel has provisions for link quality estimation and for fairly
   arbitrary metrics.  When configured suitably, Babel can implement
   shortest-path routing, or it may use a metric based, for example, on
   measured packet loss.

   Babel nodes will successfully establish an association even when they
   are configured with different parameters.  For example, a mobile node
   that is low on battery may choose to use larger time constants (hello
   and update intervals, etc.) than a node that has access to wall



Chroboczek                    Experimental                      [Page 3]
RFC 6126               The Babel Routing Protocol             April 2011


   power.  Conversely, a node that detects high levels of mobility may
   choose to use smaller time constants.  The ability to build such
   heterogeneous networks makes Babel particularly adapted to the
   wireless environment.

   Finally, Babel is a hybrid routing protocol, in the sense that it can
   carry routes for multiple network-layer protocols (IPv4 and IPv6),
   whichever protocol the Babel packets are themselves being carried
   over.

1.2.  Limitations

   Babel has two limitations that make it unsuitable for use in some
   environments.  First, Babel relies on periodic routing table updates
   rather than using a reliable transport; hence, in large, stable
   networks it generates more traffic than protocols that only send
   updates when the network topology changes.  In such networks,
   protocols such as OSPF [OSPF], IS-IS [IS-IS], or the Enhanced
   Interior Gateway Routing Protocol (EIGRP) [EIGRP] might be more
   suitable.

   Second, Babel does impose a hold time when a prefix is retracted
   (Section 3.5.5).  While this hold time does not apply to the exact
   prefix being retracted, and hence does not prevent fast reconvergence
   should it become available again, it does apply to any shorter prefix
   that covers it.  Hence, if a previously deaggregated prefix becomes
   aggregated, it will be unreachable for a few minutes.  This makes
   Babel unsuitable for use in mobile networks that implement automatic
   prefix aggregation.

1.3.  Specification of Requirements

   The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
   "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
   document are to be interpreted as described in [RFC2119].

2.  Conceptual Description of the Protocol

   Babel is a mostly loop-free distance vector protocol: it is based on
   the Bellman-Ford protocol, just like the venerable RIP [RIP], but
   includes a number of refinements that either prevent loop formation
   altogether, or ensure that a loop disappears in a timely manner and
   doesn't form again.

   Conceptually, Bellman-Ford is executed in parallel for every source
   of routing information (destination of data traffic).  In the
   following discussion, we fix a source S; the reader will recall that
   the same algorithm is executed for all sources.



Chroboczek                    Experimental                      [Page 4]
RFC 6126               The Babel Routing Protocol             April 2011


2.1.  Costs, Metrics, and Neighbourship

   As many routing algorithms, Babel computes costs of links between any
   two neighbouring nodes, abstract values attached to the edges between
   two nodes.  We write C(A, B) for the cost of the edge from node A to
   node B.

   Given a route between any two nodes, the metric of the route is the
   sum of the costs of all the edges along the route.  The goal of the
   routing algorithm is to compute, for every source S, the tree of the
   routes of lowest metric to S.

   Costs and metrics need not be integers.  In general, they can be
   values in any algebra that satisfies two fairly general conditions
   (Section 3.5.2).

   A Babel node periodically broadcasts Hello messages to all of its
   neighbours; it also periodically sends an IHU ("I Heard You") message
   to every neighbour from which it has recently heard a Hello.  From
   the information derived from Hello and IHU messages received from its
   neighbour B, a node A computes the cost C(A, B) of the link from A to
   B.

2.2.  The Bellman-Ford Algorithm

   Every node A maintains two pieces of data: its estimated distance to
   S, written D(A), and its next-hop router to S, written NH(A).
   Initially, D(S) = 0, D(A) is infinite, and NH(A) is undefined.

   Periodically, every node B sends to all of its neighbours a route
   update, a message containing D(B).  When a neighbour A of B receives
   the route update, it checks whether B is its selected next hop; if
   that is the case, then NH(A) is set to B, and D(A) is set to C(A, B)
   + D(B).  If that is not the case, then A compares C(A, B) + D(B) to
   its current value of D(A).  If that value is smaller, meaning that
   the received update advertises a route that is better than the
   currently selected route, then NH(A) is set to B, and D(A) is set to
   C(A, B) + D(B).

   A number of refinements to this algorithm are possible, and are used
   by Babel.  In particular, convergence speed may be increased by
   sending unscheduled "triggered updates" whenever a major change in
   the topology is detected, in addition to the regular, scheduled
   updates.  Additionally, a node may maintain a number of alternate
   routes, which are being advertised by neighbours other than its
   selected neighbour, and which can be used immediately if the selected
   route were to fail.




Chroboczek                    Experimental                      [Page 5]
RFC 6126               The Babel Routing Protocol             April 2011


2.3.  Transient Loops in Bellman-Ford

   It is well known that a naive application of Bellman-Ford to
   distributed routing can cause transient loops after a topology
   change.  Consider for example the following diagram:

            B
         1 /|
      1   / |
   S --- A  |1
          \ |
         1 \|
            C

   After convergence, D(B) = D(C) = 2, with NH(B) = NH(C) = A.

   Suppose now that the link between S and A fails:

            B
         1 /|
          / |
   S     A  |1
          \ |
         1 \|
            C

   When it detects the failure of the link, A switches its next hop to B
   (which is still advertising a route to S with metric 2), and
   advertises a metric equal to 3, and then advertises a new route with
   metric 3.  This process of nodes changing selected neighbours and
   increasing their metric continues until the advertised metric reaches
   "infinity", a value larger than all the metrics that the routing
   protocol is able to carry.

2.4.  Feasibility Conditions

   Bellman-Ford is a very robust algorithm: its convergence properties
   are preserved when routers delay route acquisition or when they
   discard some updates.  Babel routers discard received route
   announcements unless they can prove that accepting them cannot
   possibly cause a routing loop.

   More formally, we define a condition over route announcements, known
   as the feasibility condition, that guarantees the absence of routing
   loops whenever all routers ignore route updates that do not satisfy
   the feasibility condition.  In effect, this makes Bellman-Ford into a
   family of routing algorithms, parameterised by the feasibility
   condition.



Chroboczek                    Experimental                      [Page 6]
RFC 6126               The Babel Routing Protocol             April 2011


   Many different feasibility conditions are possible.  For example, BGP
   can be modelled as being a distance-vector protocol with a (rather
   drastic) feasibility condition: a routing update is only accepted
   when the receiving node's AS number is not included in the update's
   AS-Path attribute (note that BGP's feasibility condition does not
   ensure the absence of transitory "micro-loops" during reconvergence).

   Another simple feasibility condition, used in Destination-Sequenced
   Distance-Vector (DSDV) routing [DSDV] and in Ad hoc On-Demand
   Distance Vector (AODV) routing, stems from the following observation:
   a routing loop can only arise after a router has switched to a route
   with a larger metric than the route that it had previously selected.
   Hence, one could decide that a route is feasible only when its metric
   at the local node would be no larger than the metric of the currently
   selected route, i.e., an announcement carrying a metric D(B) is
   accepted by A when C(A, B) + D(B) <= D(A).  If all routers obey this
   constraint, then the metric at every router is nonincreasing, and the
   following invariant is always preserved: if A has selected B as its
   successor, then D(B) < D(A), which implies that the forwarding graph
   is loop-free.

   Babel uses a slightly more refined feasibility condition, used in
   EIGRP [DUAL].  Given a router A, define the feasibility distance of
   A, written FD(A), as the smallest metric that A has ever advertised
   for S to any of its neighbours.  An update sent by a neighbour B of A
   is feasible when the metric D(B) advertised by B is strictly smaller
   than A's feasibility distance, i.e., when D(B) < FD(A).

   It is easy to see that this latter condition is no more restrictive
   than DSDV-feasibility.  Suppose that node A obeys DSDV-feasibility;
   then D(A) is nonincreasing, hence at all times D(A) <= FD(A).
   Suppose now that A receives a DSDV-feasible update that advertises a
   metric D(B).  Since the update is DSDV-feasible, C(A, B) + D(B) <=
   D(A), hence D(B) < D(A), and since D(A) <= FD(A), D(B) < FD(A).

   To see that it is strictly less restrictive, consider the following
   diagram, where A has selected the route through B, and D(A) = FD(A) =
   2.  Since D(C) = 1 < FD(A), the alternate route through C is feasible
   for A, although its metric C(A, C) + D(C) = 5 is larger than that of
   the currently selected route:

      B
   1 / \ 1
    /   \
   S     A
    \   /
   1 \ / 4
      C



Chroboczek                    Experimental                      [Page 7]
RFC 6126               The Babel Routing Protocol             April 2011


   To show that this feasibility condition still guarantees loop-
   freedom, recall that at the time when A accepts an update from B, the
   metric D(B) announced by B is no smaller than FD(B); since it is
   smaller than FD(A), at that point in time FD(B) < FD(A).  Since this
   property is preserved when A sends updates, it remains true at all
   times, which ensures that the forwarding graph has no loops.

2.5.  Solving Starvation: Sequencing Routes

   Obviously, the feasibility conditions defined above cause starvation
   when a router runs out of feasible routes.  Consider the following
   diagram, where both A and B have selected the direct route to S:

      A
   1 /|        D(A) = 1
    / |       FD(A) = 1
   S  |1
    \ |        D(B) = 2
   2 \|       FD(B) = 2
      B

   Suppose now that the link between A and S breaks:

      A
      |
      |       FD(A) = 1
   S  |1
    \ |        D(B) = 2
   2 \|       FD(B) = 2
      B

   The only route available from A to S, the one that goes through B, is
   not feasible: A suffers from a spurious starvation.

   At this point, the whole network must be rebooted in order to solve
   the starvation; this is essentially what EIGRP does when it performs
   a global synchronisation of all the routers in the network with the
   source (the "active" phase of EIGRP).

   Babel reacts to starvation in a less drastic manner, by using
   sequenced routes, a technique introduced by DSDV and adopted by AODV.
   In addition to a metric, every route carries a sequence number, a
   nondecreasing integer that is propagated unchanged through the
   network and is only ever incremented by the source; a pair (s, m),
   where s is a sequence number and m a metric, is called a distance.

   A received update is feasible when either it is more recent than the
   feasibility distance maintained by the receiving node, or it is



Chroboczek                    Experimental                      [Page 8]
RFC 6126               The Babel Routing Protocol             April 2011


   equally recent and the metric is strictly smaller.  More formally, if
   FD(A) = (s, m), then an update carrying the distance (s', m') is
   feasible when either s' > s, or s = s' and m' < m.

   Assuming the sequence number of S is 137, the diagram above becomes:

      A
      |
      |       FD(A) = (137, 1)
   S  |1
    \ |        D(B) = (137, 2)
   2 \|       FD(B) = (137, 2)
      B

   After S increases its sequence number, and the new sequence number is
   propagated to B, we have:

      A
      |
      |       FD(A) = (137, 1)
   S  |1
    \ |        D(B) = (138, 2)
   2 \|       FD(B) = (138, 2)
      B

   at which point the route through B becomes feasible again.

   Note that while sequence numbers are used for determining
   feasibility, they are not necessarily used in route selection: a node
   will normally ignore the sequence number when selecting a route
   (Section 3.6).

2.6.  Requests

   In DSDV, the sequence number of a source is increased periodically.
   A route becomes feasible again after the source increases its
   sequence number, and the new sequence number is propagated through
   the network, which may, in general, require a significant amount of
   time.

   Babel takes a different approach.  When a node detects that it is
   suffering from a potentially spurious starvation, it sends an
   explicit request to the source for a new sequence number.  This
   request is forwarded hop by hop to the source, with no regard to the
   feasibility condition.  Upon receiving the request, the source
   increases its sequence number and broadcasts an update, which is
   forwarded to the requesting node.




Chroboczek                    Experimental                      [Page 9]
RFC 6126               The Babel Routing Protocol             April 2011


   Note that after a change in network topology not all such requests
   will, in general, reach the source, as some will be sent over links
   that are now broken.  However, if the network is still connected,
   then at least one among the nodes suffering from spurious starvation
   has an (unfeasible) route to the source; hence, in the absence of
   packet loss, at least one such request will reach the source.
   (Resending requests a small number of times compensates for packet
   loss.)

   Since requests are forwarded with no regard to the feasibility
   condition, they may, in general, be caught in a forwarding loop; this
   is avoided by having nodes perform duplicate detection for the
   requests that they forward.

2.7.  Multiple Routers

   The above discussion assumes that every prefix is originated by a
   single router.  In real networks, however, it is often necessary to
   have a single prefix originated by multiple routers; for example, the
   default route will be originated by all of the edge routers of a
   routing domain.

   Since synchronising sequence numbers between distinct routers is
   problematic, Babel treats routes for the same prefix as distinct
   entities when they are originated by different routers: every route
   announcement carries the router-id of its originating router, and
   feasibility distances are not maintained per prefix, but per source,
   where a source is a pair of a router-id and a prefix.  In effect,
   Babel guarantees loop-freedom for the forwarding graph to every
   source; since the union of multiple acyclic graphs is not in general
   acyclic, Babel does not in general guarantee loop-freedom when a
   prefix is originated by multiple routers, but any loops will be
   broken in a time at most proportional to the diameter of the loop --
   as soon as an update has "gone around" the routing loop.

   Consider for example the following diagram, where A has selected the
   default route through S, and B has selected the one through S':

              1     1     1
   ::/0 -- S --- A --- B --- S' -- ::/0

   Suppose that both default routes fail at the same time; then nothing
   prevents A from switching to B, and B simultaneously switching to A.
   However, as soon as A has successfully advertised the new route to B,
   the route through A will become unfeasible for B.  Conversely, as
   soon as B will have advertised the route through A, the route through
   B will become unfeasible for A.




Chroboczek                    Experimental                     [Page 10]
RFC 6126               The Babel Routing Protocol             April 2011


   In effect, the routing loop disappears at the latest when routing
   information has gone around the loop.  Since this process can be
   delayed by lost packets, Babel makes certain efforts to ensure that
   updates are sent reliably after a router-id change.

   Additionally, after the routers have advertised the two routes, both
   sources will be in their source tables, which will prevent them from
   ever again participating in a routing loop involving routes from S
   and S' (up to the source GC time, which, available memory permitting,
   can be set to arbitrarily large values).

2.8.  Overlapping Prefixes

   In the above discussion, we have assumed that all prefixes are
   disjoint, as is the case in flat ("mesh") routing.  In practice,
   however, prefixes may overlap: for example, the default route
   overlaps with all of the routes present in the network.

   After a route fails, it is not correct in general to switch to a
   route that subsumes the failed route.  Consider for example the
   following configuration:

              1     1
   ::/0 -- A --- B --- C

   Suppose that node C fails.  If B forwards packets destined to C by
   following the default route, a routing loop will form, and persist
   until A learns of B's retraction of the direct route to C.  Babel
   avoids this pitfall by maintaining an "unreachable" route for a few
   minutes after a route is retracted; the time for which such a route
   must be maintained should be the worst-case propagation time of the
   retraction of the route to C.

3.  Protocol Operation

   Every Babel speaker is assigned a router-id, which is an arbitrary
   string of 8 octets that is assumed unique across the routing domain.
   We suggest that router-ids should be assigned in modified EUI-64
   format [ADDRARCH].  (As a matter of fact, the protocol encoding is
   slightly more compact when router-ids are assigned in the same manner
   as the IPv6 layer assigns host IDs.)

3.1.  Message Transmission and Reception

   Babel protocol packets are sent in the body of a UDP datagram.  Each
   Babel packet consists of one or more TLVs.





Chroboczek                    Experimental                     [Page 11]
RFC 6126               The Babel Routing Protocol             April 2011


   The source address of a Babel packet is always a unicast address,
   link-local in the case of IPv6.  Babel packets may be sent to a well-
   known (link-local) multicast address (this is the usual case) or to a
   (link-local) unicast address.  In normal operation, a Babel speaker
   sends both multicast and unicast packets to its neighbours.

   With the exception of Hello TLVs and acknowledgements, all Babel TLVs
   can be sent to either unicast or multicast addresses, and their
   semantics does not depend on whether the destination was a unicast or
   multicast address.  Hence, a Babel speaker does not need to determine
   the destination address of a packet that it receives in order to
   interpret it.

   A moderate amount of jitter is applied to packets sent by a Babel
   speaker: outgoing TLVs are buffered and SHOULD be sent with a small
   random delay.  This is done for two purposes: it avoids
   synchronisation of multiple Babel speakers across a network [JITTER],
   and it allows for the aggregation of multiple TLVs into a single
   packet.

   The exact delay and amount of jitter applied to a packet depends on
   whether it contains any urgent TLVs.  Acknowledgement TLVs MUST be
   sent before the deadline specified in the corresponding request.  The
   particular class of updates specified in Section 3.7.2 MUST be sent
   in a timely manner.  The particular class of request and update TLVs
   specified in Section 3.8.2 SHOULD be sent in a timely manner.

3.2.  Data Structures

   Every Babel speaker maintains a number of data structures.

3.2.1.  Sequence Number

   A node's sequence number is a 16-bit integer that is included in
   route updates sent for routes originated by this node.  A node
   increments its sequence number (modulo 2^16) whenever it receives a
   request for a new sequence number (Section 3.8.1.2).

   A node SHOULD NOT increment its sequence number (seqno)
   spontaneously, since increasing seqnos makes it less likely that
   other nodes will have feasible alternate routes when their selected
   routes fail.

3.2.2.  The Interface Table

   The interface table contains the list of interfaces on which the node
   speaks the Babel protocol.  Every interface table entry contains the
   interface's Hello seqno, a 16-bit integer that is sent with each



Chroboczek                    Experimental                     [Page 12]
RFC 6126               The Babel Routing Protocol             April 2011


   Hello TLV on this interface and is incremented (modulo 2^16) whenever
   a Hello is sent.  (Note that an interface's Hello seqno is unrelated
   to the node's seqno.)

   There are two timers associated with each interface table entry --
   the Hello timer, which governs the sending of periodic Hello and IHU
   packets, and the update timer, which governs the sending of periodic
   route updates.

3.2.3.  The Neighbour Table

   The neighbour table contains the list of all neighbouring interfaces
   from which a Babel packet has been recently received.  The neighbour
   table is indexed by pairs of the form (interface, address), and every
   neighbour table entry contains the following data:

   o  the local node's interface over which this neighbour is reachable;

   o  the address of the neighbouring interface;

   o  a history of recently received Hello packets from this neighbour;
      this can, for example, be a sequence of n bits, for some small
      value n, indicating which of the n hellos most recently sent by
      this neighbour have been received by the local node;

   o  the "transmission cost" value from the last IHU packet received
      from this neighbour, or FFFF hexadecimal (infinity) if the IHU
      hold timer for this neighbour has expired;

   o  the neighbour's expected Hello sequence number, an integer modulo
      2^16.

   There are two timers associated with each neighbour entry -- the
   hello timer, which is initialised from the interval value carried by
   Hello TLVs, and the IHU timer, which is initialised to a small
   multiple of the interval carried in IHU TLVs.

   Note that the neighbour table is indexed by IP addresses, not by
   router-ids: neighbourship is a relationship between interfaces, not
   between nodes.  Therefore, two nodes with multiple interfaces can
   participate in multiple neighbourship relationships, a fairly common
   situation when wireless nodes with multiple radios are involved.

3.2.4.  The Source Table

   The source table is used to record feasibility distances.  It is
   indexed by triples of the form (prefix, plen, router-id), and every
   source table entry contains the following data:



Chroboczek                    Experimental                     [Page 13]
RFC 6126               The Babel Routing Protocol             April 2011


   o  the prefix (prefix, plen), where plen is the prefix length, that
      this entry applies to;

   o  the router-id of a router originating this prefix;

   o  a pair (seqno, metric), this source's feasibility distance.

   There is one timer associated with each entry in the source table --
   the source garbage-collection timer.  It is initialised to a time on
   the order of minutes and reset as specified in Section 3.7.3.

3.2.5.  The Route Table

   The route table contains the routes known to this node.  It is
   indexed by triples of the form (prefix, plen, neighbour), and every
   route table entry contains the following data:

   o  the source (prefix, plen, router-id) for which this route is
      advertised;

   o  the neighbour that advertised this route;

   o  the metric with which this route was advertised by the neighbour,
      or FFFF hexadecimal (infinity) for a recently retracted route;

   o  the sequence number with which this route was advertised;

   o  the next-hop address of this route;

   o  a boolean flag indicating whether this route is selected, i.e.,
      whether it is currently being used for forwarding and is being
      advertised.

   There is one timer associated with each route table entry -- the
   route expiry timer.  It is initialised and reset as specified in
   Section 3.5.4.

3.2.6.  The Table of Pending Requests

   The table of pending requests contains a list of seqno requests that
   the local node has sent (either because they have been originated
   locally, or because they were forwarded) and to which no reply has
   been received yet.  This table is indexed by prefixes, and every
   entry in this table contains the following data:

   o  the prefix, router-id, and seqno being requested;





Chroboczek                    Experimental                     [Page 14]
RFC 6126               The Babel Routing Protocol             April 2011


   o  the neighbour, if any, on behalf of which we are forwarding this
      request;

   o  a small integer indicating the number of times that this request
      will be resent if it remains unsatisfied.

   There is one timer associated with each pending request; it governs
   both the resending of requests and their expiry.

3.3.  Acknowledged Packets

   A Babel speaker may request that any neighbour receiving a given
   packet reply with an explicit acknowledgement within a given time.
   While the use of acknowledgement requests is optional, every Babel
   speaker MUST be able to reply to such a request.

   An acknowledgement MUST be sent to a unicast destination.  On the
   other hand, acknowledgement requests may be sent to either unicast or
   multicast destinations, in which case they request an acknowledgement
   from all of the receiving nodes.

   When to request acknowledgements is a matter of local policy; the
   simplest strategy is to never request acknowledgements and to rely on
   periodic updates to ensure that any reachable routes are eventually
   propagated throughout the routing domain.  For increased efficiency,
   we suggest that acknowledged packets should be used in order to send
   urgent updates (Section 3.7.2) when the number of neighbours on a
   given interface is small.  Since Babel is designed to deal gracefully
   with packet loss on unreliable media, sending all packets with
   acknowledgement requests is not necessary, and not even recommended,
   as the acknowledgements cause additional traffic and may force
   additional Address Resolution Protocol (ARP) or Neighbour Discovery
   exchanges.

3.4.  Neighbour Acquisition

   Neighbour acquisition is the process by which a Babel node discovers
   the set of neighbours heard over each of its interfaces and
   ascertains bidirectional reachability.  On unreliable media,
   neighbour acquisition additionally provides some statistics that MAY
   be used in link quality computation.

3.4.1.  Reverse Reachability Detection

   Every Babel node sends periodic Hellos over each of its interfaces.
   Each Hello TLV carries an increasing (modulo 2^16) sequence number
   and the interval between successive periodic packets sent on this
   particular interface.



Chroboczek                    Experimental                     [Page 15]
RFC 6126               The Babel Routing Protocol             April 2011


   In addition to the periodic Hello packets, a node MAY send
   unscheduled Hello packets, e.g., to accelerate link cost estimation
   when a new neighbour is discovered, or when link conditions have
   suddenly changed.

   A node MAY change its Hello interval.  The Hello interval MAY be
   decreased at any time; it SHOULD NOT be increased, except immediately
   before sending a Hello packet.  (Equivalently, a node SHOULD send an
   unscheduled Hello immediately after increasing its Hello interval.)

   How to deal with received Hello TLVs and what statistics to maintain
   are considered local implementation matters; typically, a node will
   maintain some sort of history of recently received Hellos.  A
   possible algorithm is described in Appendix A.1.

   After receiving a Hello, or determining that it has missed one, the
   node recomputes the association's cost (Section 3.4.3) and runs the
   route selection procedure (Section 3.6).

3.4.2.  Bidirectional Reachability Detection

   In order to establish bidirectional reachability, every node sends
   periodic IHU ("I Heard You") TLVs to each of its neighbours.  Since
   IHUs carry an explicit interval value, they MAY be sent less often
   than Hellos in order to reduce the amount of routing traffic in dense
   networks; in particular, they SHOULD be sent less often than Hellos
   over links with little packet loss.  While IHUs are conceptually
   unicast, they SHOULD be sent to a multicast address in order to avoid
   an ARP or Neighbour Discovery exchange and to aggregate multiple IHUs
   in a single packet.

   In addition to the periodic IHUs, a node MAY, at any time, send an
   unscheduled IHU packet.  It MAY also, at any time, decrease its IHU
   interval, and it MAY increase its IHU interval immediately before
   sending an IHU.

   Every IHU TLV contains two pieces of data: the link's rxcost
   (reception cost) from the sender's perspective, used by the neighbour
   for computing link costs (Section 3.4.3), and the interval between
   periodic IHU packets.  A node receiving an IHU updates the value of
   the sending neighbour's txcost (transmission cost), from its
   perspective, to the value contained in the IHU, and resets this
   neighbour's IHU timer to a small multiple of the value received in
   the IHU.

   When a neighbour's IHU timer expires, its txcost is set to infinity.





Chroboczek                    Experimental                     [Page 16]
RFC 6126               The Babel Routing Protocol             April 2011


   After updating a neighbour's txcost, the receiving node recomputes
   the neighbour's cost (Section 3.4.3) and runs the route selection
   procedure (Section 3.6).

3.4.3.  Cost Computation

   A neighbourship association's link cost is computed from the values
   maintained in the neighbour table -- namely, the statistics kept in
   the neighbour table about the reception of Hellos, and the txcost
   computed from received IHU packets.

   For every neighbour, a Babel node computes a value known as this
   neighbour's rxcost.  This value is usually derived from the Hello
   history, which may be combined with other data, such as statistics
   maintained by the link layer.  The rxcost is sent to a neighbour in
   each IHU.

   How the txcost and rxcost are combined in order to compute a link's
   cost is a matter of local policy; as far as Babel's correctness is
   concerned, only the following conditions MUST be satisfied:

   o  the cost is strictly positive;

   o  if no hellos were received recently, then the cost is infinite;

   o  if the txcost is infinite, then the cost is infinite.

   Note that while this document does not constrain cost computation any
   further, not all cost computation strategies will give good results.
   We give a few examples of strategies for computing a link's cost that
   are known to work well in practice in Appendix A.2.

3.5.  Routing Table Maintenance

   Conceptually, a Babel update is a quintuple (prefix, plen, router-id,
   seqno, metric), where (prefix, plen) is the prefix for which a route
   is being advertised, router-id is the router-id of the router
   originating this update, seqno is a nondecreasing (modulo 2^16)
   integer that carries the originating router seqno, and metric is the
   announced metric.

   Before being accepted, an update is checked against the feasibility
   condition (Section 3.5.1), which ensures that the route does not
   create a routing loop.  If the feasibility condition is not
   satisfied, the update is either ignored or treated as a retraction,
   depending on some other conditions (Section 3.5.4).  If the
   feasibility condition is satisfied, then the update cannot possibly
   cause a routing loop, and the update is accepted.



Chroboczek                    Experimental                     [Page 17]
RFC 6126               The Babel Routing Protocol             April 2011


3.5.1.  The Feasibility Condition

   The feasibility condition is applied to all received updates.  The
   feasibility condition compares the metric in the received update with
   the metrics of the updates previously sent by the receiving node;
   updates with finite metrics large enough to cause a loop are
   discarded.

   A feasibility distance is a pair (seqno, metric), where seqno is an
   integer modulo 2^16 and metric is a positive integer.  Feasibility
   distances are compared lexicographically, with the first component
   inverted: we say that a distance (seqno, metric) is strictly better
   than a distance (seqno', metric'), written

      (seqno, metric) < (seqno', metric')

   when

      seqno > seqno' or (seqno = seqno' and metric < metric')

   where sequence numbers are compared modulo 2^16.

   Given a source (p, plen, id), a node's feasibility distance for this
   source is the minimum, according to the ordering defined above, of
   the distances of all the finite updates ever sent by this particular
   node for the prefix (p, plen) carrying the router-id id.  Feasibility
   distances are maintained in the source table; the exact procedure is
   given in Section 3.7.3.

   A received update is feasible when either it is a retraction (its
   metric is FFFF hexadecimal), or the advertised distance is strictly
   better, in the sense defined above, than the feasibility distance for
   the corresponding source.  More precisely, a route advertisement
   carrying the quintuple (prefix, plen, router-id, seqno, metric) is
   feasible if one of the following conditions holds:

   o  metric is infinite; or

   o  no entry exists in the source table indexed by (id, prefix, plen);
      or

   o  an entry (prefix, plen, router-id, seqno', metric') exists in the
      source table, and either

      *  seqno' < seqno or

      *  seqno = seqno' and metric < metric'.




Chroboczek                    Experimental                     [Page 18]
RFC 6126               The Babel Routing Protocol             April 2011


   Note that the feasibility condition considers the metric advertised
   by the neighbour, not the route's metric; hence, a fluctuation in a
   neighbour's cost cannot render a selected route unfeasible.

3.5.2.  Metric Computation

   A route's metric is computed from the metric advertised by the
   neighbour and the neighbour's link cost.  Just like cost computation,
   metric computation is considered a local policy matter; as far as
   Babel is concerned, the function M(c, m) used for computing a metric
   from a locally computed link cost and the metric advertised by a
   neighbour MUST only satisfy the following conditions:

   o  if c is infinite, then M(c, m) is infinite;

   o  M is strictly monotonic: M(c, m) > m.

   Additionally, the metric SHOULD satisfy the following condition:

   o  M is isotonic: if m <= m', then M(c, m) <= M(c, m').

   Note that while strict monotonicity is essential to the integrity of
   the network (persistent routing loops may appear if it is not
   satisfied), isotonicity is not: if it is not satisfied, Babel will
   still converge to a locally optimal routing table, but might not
   reach a global optimum (in fact, such a global optimum may not even
   exist).

   As with cost computation, not all strategies for computing route
   metrics will give good results.  In particular, some metrics are more
   likely than others to lead to routing instabilities (route flapping).
   In Appendix A.3, we give a number of examples of strictly monotonic,
   isotonic routing metrics that are known to work well in practice.

3.5.3.  Encoding of Updates

   In a large network, the bulk of Babel traffic consists of route
   updates; hence, some care has been given to encoding them
   efficiently.  An Update TLV itself only contains the prefix, seqno,
   and metric, while the next hop is derived either from the network-
   layer source address of the packet or from an explicit Next Hop TLV
   in the same packet.  The router-id is derived from a separate
   Router-Id TLV in the same packet, which optimises the case when
   multiple updates are sent with the same router-id.

   Additionally, a prefix of the advertised prefix can be omitted in an
   Update TLV, in which case it is copied from a previous Update TLV in
   the same packet -- this is known as address compression [PACKETBB].



Chroboczek                    Experimental                     [Page 19]
RFC 6126               The Babel Routing Protocol             April 2011


   Finally, as a special optimisation for the case when a router-id
   coincides with the interface-id part of an IPv6 address, the
   router-id can optionally be derived from the low-order bits of the
   advertised prefix.

   The encoding of updates is described in detail in Section 4.4.

3.5.4.  Route Acquisition

   When a Babel node receives an update (id, prefix, seqno, metric) from
   a neighbour neigh with a link cost value equal to cost, it checks
   whether it already has a routing table entry indexed by (neigh, id,
   prefix).

   If no such entry exists:

   o  if the update is unfeasible, it is ignored;

   o  if the metric is infinite (the update is a retraction), the update
      is ignored;

   o  otherwise, a new route table entry is created, indexed by (neigh,
      id, prefix), with seqno equal to seqno and an advertised metric
      equal to the metric carried by the update.

   If such an entry exists:

   o  if the entry is currently installed and the update is unfeasible,
      then the behaviour depends on whether the router-ids of the two
      entries match.  If the router-ids are different, the update is
      treated as though it were a retraction (i.e., as though the metric
      were FFFF hexadecimal).  If the router-ids are equal, the update
      is ignored;

   o  otherwise (i.e., if either the update is feasible or the entry is
      not currently installed), then the entry's sequence number,
      advertised metric, metric, and router-id are updated and, unless
      the advertised metric is infinite, the route's expiry timer is
      reset to a small multiple of the Interval value included in the
      update.

   When a route's expiry timer triggers, the behaviour depends on
   whether the route's metric is finite.  If the metric is finite, it is
   set to infinity and the expiry timer is reset.  If the metric is
   already infinite, the route is flushed from the route table.

   After the routing table is updated, the route selection procedure
   (Section 3.6) is run.



Chroboczek                    Experimental                     [Page 20]
RFC 6126               The Babel Routing Protocol             April 2011


3.5.5.  Hold Time

   When a prefix p is retracted, because all routes are unfeasible, too
   old, or have an infinite metric, and a shorter prefix p' that covers
   p is reachable, p' cannot in general be used for routing packets
   destined to p without running the risk of creating a routing loop
   (Section 2.8).

   To avoid this issue, whenever a prefix is retracted, a routing table
   entry with infinite metric is maintained as described in
   Section 3.5.4 above, and packets destined for that prefix MUST NOT be
   forwarded by following a route for a shorter prefix.  The infinite
   metric entry is maintained until it is superseded by a feasible
   update; if no such update arrives within the route hold time, the
   entry is flushed.

3.6.  Route Selection

   Route selection is the process by which a single route for a given
   prefix is selected to be used for forwarding packets and to be
   re-advertised to a node's neighbours.

   Babel is designed to allow flexible route selection policies.  As far
   as the protocol's correctness is concerned, the route selection
   policy MUST only satisfy the following properties:

   o  a route with infinite metric (a retracted route) is never
      selected;

   o  an unfeasible route is never selected.

   Note, however, that Babel does not naturally guarantee the stability
   of routing, and configuring conflicting route selection policies on
   different routers may lead to persistent route oscillation.

   Defining a good route selection policy for Babel is an open research
   problem.  Route selection can take into account multiple mutually
   contradictory criteria; in roughly decreasing order of importance,
   these are:

   o  routes with a small metric should be preferred over routes with a
      large metric;

   o  switching router-ids should be avoided;

   o  routes through stable neighbours should be preferred over routes
      through unstable ones;




Chroboczek                    Experimental                     [Page 21]
RFC 6126               The Babel Routing Protocol             April 2011


   o  stable routes should be preferred over unstable ones;

   o  switching next hops should be avoided.

   A simple strategy is to choose the feasible route with the smallest
   metric, with a small amount of hysteresis applied to avoid switching
   router-ids.

   After the route selection procedure is run, triggered updates
   (Section 3.7.2) and requests (Section 3.8.2) are sent.

3.7.  Sending Updates

   A Babel speaker advertises to its neighbours its set of selected
   routes.  Normally, this is done by sending one or more multicast
   packets containing Update TLVs on all of its connected interfaces;
   however, on link technologies where multicast is significantly more
   expensive than unicast, a node MAY choose to send multiple copies of
   updates in unicast packets when the number of neighbours is small.

   Additionally, in order to ensure that any black-holes are reliably
   cleared in a timely manner, a Babel node sends retractions (updates
   with an infinite metric) for any recently retracted prefixes.

   If an update is for a route injected into the Babel domain by the
   local node (e.g., the address of a local interface, the prefix of a
   directly attached network, or redistributed from a different routing
   protocol), the router-id is set to the local id, the metric is set to
   some arbitrary finite value (typically 0), and the seqno is set to
   the local router's sequence number.

   If an update is for a route learned from another Babel speaker, the
   router-id and sequence number are copied from the routing table
   entry, and the metric is computed as specified in Section 3.5.2.

3.7.1.  Periodic Updates

   Every Babel speaker periodically advertises all of its selected
   routes on all of its interfaces, including any recently retracted
   routes.  Since Babel doesn't suffer from routing loops (there is no
   "counting to infinity") and relies heavily on triggered updates
   (Section 3.7.2), this full dump only needs to happen infrequently.

3.7.2.  Triggered Updates

   In addition to the periodic routing updates, a Babel speaker sends
   unscheduled, or triggered, updates in order to inform its neighbours
   of a significant change in the network topology.



Chroboczek                    Experimental                     [Page 22]
RFC 6126               The Babel Routing Protocol             April 2011


   A change of router-id for the selected route to a given prefix may be
   indicative of a routing loop in formation; hence, a node MUST send a
   triggered update in a timely manner whenever it changes the selected
   router-id for a given destination.  Additionally, it SHOULD make a
   reasonable attempt at ensuring that all neighbours receive this
   update.

   There are two strategies for ensuring that.  If the number of
   neighbours is small, then it is reasonable to send the update
   together with an acknowledgement request; the update is resent until
   all neighbours have acknowledged the packet, up to some number of
   times.  If the number of neighbours is large, however, requesting
   acknowledgements from all of them might cause a non-negligible amount
   of network traffic; in that case, it may be preferable to simply
   repeat the update some reasonable number of times (say, 5 for
   wireless and 2 for wired links).

   A route retraction is somewhat less worrying: if the route retraction
   doesn't reach all neighbours, a black-hole might be created, which,
   unlike a routing loop, does not endanger the integrity of the
   network.  When a route is retracted, a node SHOULD send a triggered
   update and SHOULD make a reasonable attempt at ensuring that all
   neighbours receive this retraction.

   Finally, a node MAY send a triggered update when the metric for a
   given prefix changes in a significant manner, either due to a
   received update or because a link cost has changed.  A node SHOULD
   NOT send triggered updates for other reasons, such as when there is a
   minor fluctuation in a route's metric, when the selected next hop
   changes, or to propagate a new sequence number (except to satisfy a
   request, as specified in Section 3.8).

3.7.3.  Maintaining Feasibility Distances

   Before sending an update (prefix, plen, router-id, seqno, metric)
   with finite metric (i.e., not a route retraction), a Babel node
   updates the feasibility distance maintained in the source table.
   This is done as follows.

   If no entry indexed by (prefix, plen, router-id) exists in the source
   table, then one is created with value (prefix, plen, router-id,
   seqno, metric).

   If an entry (prefix, plen, router-id, seqno', metric') exists, then
   it is updated as follows:

   o  if seqno > seqno', then seqno' := seqno, metric' := metric;




Chroboczek                    Experimental                     [Page 23]
RFC 6126               The Babel Routing Protocol             April 2011


   o  if seqno = seqno' and metric' > metric, then metric' := metric;

   o  otherwise, nothing needs to be done.

   The garbage-collection timer for the modified entry is then reset.
   Note that the garbage-collection timer is not reset when a retraction
   is sent.

3.7.4.  Split Horizon

   When running over a transitive, symmetric link technology, e.g., a
   point-to-point link or a wired LAN technology such as Ethernet, a
   Babel node SHOULD use an optimisation known as split horizon.  When
   split horizon is used on a given interface, a routing update is not
   sent on this particular interface when the advertised route was
   learnt from a neighbour over the same interface.

   Split horizon SHOULD NOT be applied to an interface unless the
   interface is known to be symmetric and transitive; in particular,
   split horizon is not applicable to decentralised wireless link
   technologies (e.g., IEEE 802.11 in ad hoc mode).

3.8.  Explicit Route Requests

   In normal operation, a node's routing table is populated by the
   regular and triggered updates sent by its neighbours.  Under some
   circumstances, however, a node sends explicit requests to cause a
   resynchronisation with the source after a mobility event or to
   prevent a route from spuriously expiring.

   The Babel protocol provides two kinds of explicit requests: route
   requests, which simply request an update for a given prefix, and
   seqno requests, which request an update for a given prefix with a
   specific sequence number.  The former are never forwarded; the latter
   are forwarded if they cannot be satisfied by a neighbour.

3.8.1.  Handling Requests

   Upon receiving a request, a node either forwards the request or sends
   an update in reply to the request, as described in the following
   sections.  If this causes an update to be sent, the update is either
   sent to a multicast address on the interface on which the request was
   received, or to the unicast address of the neighbour that sent the
   update.

   The exact behaviour is different for route requests and seqno
   requests.




Chroboczek                    Experimental                     [Page 24]
RFC 6126               The Babel Routing Protocol             April 2011


3.8.1.1.  Route Requests

   When a node receives a route request for a prefix (prefix, plen), it
   checks its route table for a selected route to this exact prefix.  If
   such a route exists, it MUST send an update; if such a route does
   not, it MUST send a retraction for that prefix.

   When a node receives a wildcard route request, it SHOULD send a full
   routing table dump.

3.8.1.2.  Seqno Requests

   When a node receives a seqno request for a given router-id and
   sequence number, it checks whether its routing table contains a
   selected entry for that prefix; if no such entry exists, or the entry
   has infinite metric, it ignores the request.

   If a selected route for the given prefix exists, and either the
   router-ids are different or the router-ids are equal and the entry's
   sequence number is no smaller than the requested sequence number, it
   MUST send an update for the given prefix.

   If the router-ids match but the requested seqno is larger than the
   route entry's, the node compares the router-id against its own
   router-id.  If the router-id is its own, then it increases its
   sequence number by 1 and sends an update.  A node MUST NOT increase
   its sequence number by more than 1 in response to a route request.

   If the requested router-id is not its own, the received request's hop
   count is 2 or more, and the node has a route (not necessarily a
   feasible one) for the requested prefix that does not use the
   requestor as a next hop, the node SHOULD forward the request.  It
   does so by decreasing the hop count and sending the request in a
   unicast packet destined to a neighbour that advertises the given
   prefix (not necessarily the selected neighbour) and that is distinct
   from the neighbour from which the request was received.

   A node SHOULD maintain a list of recently forwarded requests and
   forward the reply in a timely manner.  A node SHOULD compare every
   incoming request against its list of recently forwarded requests and
   avoid forwarding it if it is redundant.

   Since the request-forwarding mechanism does not necessarily obey the
   feasibility condition, it may get caught in routing loops; hence,
   requests carry a hop count to limit the time for which they remain in
   the network.  However, since requests are only ever forwarded as
   unicast packets, the initial hop count need not be kept particularly




Chroboczek                    Experimental                     [Page 25]
RFC 6126               The Babel Routing Protocol             April 2011


   low, and performing an expanding horizon search is not necessary.  A
   request MUST NOT be forwarded to a multicast address, and it MUST be
   forwarded to a single neighbour only.

3.8.2.  Sending Requests

   A Babel node MAY send a route or seqno request at any time, to a
   multicast or a unicast address; there is only one case when
   originating requests is required (Section 3.8.2.1).

3.8.2.1.  Avoiding Starvation

   When a route is retracted or expires, a Babel node usually switches
   to another feasible route for the same prefix.  It may be the case,
   however, that no such routes are available.

   A node that has lost all feasible routes to a given destination MUST
   send a seqno request.  The router-id of the request is set to the
   router-id of the route that it has just lost, and the requested seqno
   is the value contained in the source table, plus 1.

   Such a request SHOULD be multicast over all of the node's attached
   interfaces.  Similar requests will be sent by other nodes that are
   affected by the route's loss and will be forwarded by neighbouring
   nodes up to the source.  If the network is connected, and there is no
   packet loss, this will result in a route being advertised with a new
   sequence number.  (Note that, due to duplicate suppression, only a
   small number of such requests will actually reach the source.)

   In order to compensate for packet loss, a node SHOULD repeat such a
   request a small number of times if no route becomes feasible within a
   short time.  Under heavy packet loss, however, all such requests may
   be lost; in that case, the second mechanism in the next section will
   eventually ensure that a new seqno is received.

3.8.2.2.  Dealing with Unfeasible Updates

   When a route's metric increases, a node might receive an unfeasible
   update for a route that it has currently selected.  As specified in
   Section 3.5.1, the receiving node will either ignore the update or
   retract the route.

   In order to keep routes from spuriously expiring because they have
   become unfeasible, a node SHOULD send a unicast seqno request
   whenever it receives an unfeasible update for a route that is
   currently selected.  The requested sequence number is computed from
   the source table as above.




Chroboczek                    Experimental                     [Page 26]
RFC 6126               The Babel Routing Protocol             April 2011


   Additionally, a node SHOULD send a unicast seqno request whenever it
   receives an unfeasible update from a currently unselected neighbour
   that is "good enough", i.e., that would lead to the received route
   becoming selected were it feasible.

3.8.2.3.  Preventing Routes from Expiring

   In normal operation, a route's expiry timer should never trigger:
   since a route's hold time is computed from an explicit interval
   included in Update TLVs, a new update should arrive in time to
   prevent a route from expiring.

   In the presence of packet loss, however, it may be the case that no
   update is successfully received for an extended period of time,
   causing a route to expire.  In order to avoid such spurious expiry,
   shortly before a selected route expires, a Babel node SHOULD send a
   unicast route request to the neighbour that advertised this route;
   since nodes always send retractions in response to non-wildcard route
   requests (Section 3.8.1.1), this will usually result in either the
   route being refreshed or a retraction being received.

3.8.2.4.  Acquiring New Neighbours

   In order to speed up convergence after a mobility event, a node MAY
   send a unicast wildcard request after acquiring a new neighbour.
   Additionally, a node MAY send a small number of multicast wildcard
   requests shortly after booting.

4.  Protocol Encoding

   A Babel packet is sent as the body of a UDP datagram, with network-
   layer hop count set to 1, destined to a well-known multicast address
   or to a unicast address, over IPv4 or IPv6; in the case of IPv6,
   these addresses are link-local.  Both the source and destination UDP
   port are set to a well-known port number.  A Babel packet MUST be
   silently ignored unless its source address is either a link-local
   IPv6 address, or an IPv4 address belonging to the local network, and
   its source port is the well-known Babel port.  Babel packets MUST NOT
   be sent as IPv6 Jumbograms.

   In order to minimise the number of packets being sent while avoiding
   lower-layer fragmentation, a Babel node SHOULD attempt to maximise
   the size of the packets it sends, up to the outgoing interface's MTU
   adjusted for lower-layer headers (28 octets for UDP/IPv4, 48 octets
   for UDP/IPv6).  It MUST NOT send packets larger than the attached
   interface's MTU (adjusted for lower-layer headers) or 512 octets,
   whichever is larger, but not exceeding 2^16 - 1 adjusted for lower-




Chroboczek                    Experimental                     [Page 27]
RFC 6126               The Babel Routing Protocol             April 2011


   layer headers.  Every Babel speaker MUST be able to receive packets
   that are as large as any attached interface's MTU (adjusted for
   lower-layer headers) or 512 octets, whichever is larger.

   In order to avoid global synchronisation of a Babel network and to
   aggregate multiple TLVs into large packets, a Babel node MUST buffer
   every TLV and delay sending a UDP packet by a small, randomly chosen
   delay [JITTER].  In order to allow accurate computation of packet
   loss rates, this delay MUST NOT be larger than half the advertised
   Hello interval.

4.1.  Data Types

4.1.1.  Interval

   Relative times are carried as 16-bit values specifying a number of
   centiseconds (hundredths of a second).  This allows times up to
   roughly 11 minutes with a granularity of 10 ms, which should cover
   all reasonable applications of Babel.

4.1.2.  Router-Id

   A router-id is an arbitrary 8-octet value.  Router-ids SHOULD be
   assigned in modified EUI-64 format [ADDRARCH].

4.1.3.  Address

   Since the bulk of the protocol is taken by addresses, multiple ways
   of encoding addresses are defined.  Additionally, a common subnet
   prefix may be omitted when multiple addresses are sent in a single
   packet -- this is known as address compression [PACKETBB].

   Address encodings:

   o  AE 0: wildcard address.  The value is 0 octets long.

   o  AE 1: IPv4 address.  Compression is allowed. 4 octets or less.

   o  AE 2: IPv6 address.  Compression is allowed. 16 octets or less.

   o  AE 3: link-local IPv6 address.  The value is 8 octets long, a
      prefix of fe80::/64 is implied.

   The address family of an address is either IPv4 or IPv6; it is
   undefined for AE 0, IPv4 for AE 1, and IPv6 for AE 2 and 3.






Chroboczek                    Experimental                     [Page 28]
RFC 6126               The Babel Routing Protocol             April 2011


4.1.4.  Prefixes

   A network prefix is encoded just like a network address, but it is
   stored in the smallest number of octets that are enough to hold the
   significant bits (up to the prefix length).

4.2.  Packet Format

   A Babel packet consists of a 4-octet header, followed by a sequence
   of TLVs.

   0                   1                   2                   3
   0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |     Magic     |    Version    |        Body length            |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |   Packet Body ...
   +-+-+-+-+-+-+-+-+-+-+-+-+-

   Fields :

   Magic     The arbitrary but carefully chosen value 42 (decimal);
             packets with a first octet different from 42 MUST be
             silently ignored.

   Version   This document specifies version 2 of the Babel protocol.
             Packets with a second octet different from 2 MUST be
             silently ignored.

   Body length  The length in octets of the body following the packet
                header.

   Body      The packet body; a sequence of TLVs.

   Any data following the body MUST be silently ignored.

4.3.  TLV Format

   With the exception of Pad1, all TLVs have the following structure:

   0                   1                   2                   3
   0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |     Type      |    Length     |     Body...
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-






Chroboczek                    Experimental                     [Page 29]
RFC 6126               The Babel Routing Protocol             April 2011


   Fields :

   Type      The type of the TLV.

   Length    The length of the body, exclusive of the Type and Length
             fields.  If the body is longer than the expected length of
             a given type of TLV, any extra data MUST be silently
             ignored.

   Body      The TLV body, the interpretation of which depends on the
             type.

   TLVs with an unknown type value MUST be silently ignored.

4.4.  Details of Specific TLVs

4.4.1.  Pad1

   0
   0 1 2 3 4 5 6 7
   +-+-+-+-+-+-+-+-+
   |   Type = 0    |
   +-+-+-+-+-+-+-+-+

   Fields :

   Type      Set to 0 to indicate a Pad1 TLV.

   This TLV is silently ignored on reception.

4.4.2.  PadN

   0                   1                   2                   3
   0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |    Type = 1   |    Length     |      MBZ...
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-

   Fields :

   Type      Set to 1 to indicate a PadN TLV.

   Length    The length of the body, exclusive of the Type and Length
             fields.

   MBZ       Set to 0 on transmission.

   This TLV is silently ignored on reception.



Chroboczek                    Experimental                     [Page 30]
RFC 6126               The Babel Routing Protocol             April 2011


4.4.3.  Acknowledgement Request

   0                   1                   2                   3
   0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |    Type = 2   |    Length     |          Reserved             |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |            Nonce              |          Interval             |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

   This TLV requests that the receiver send an Acknowledgement TLV
   within the number of centiseconds specified by the Interval field.

   Fields :

   Type      Set to 2 to indicate an Acknowledgement Request TLV.

   Length    The length of the body, exclusive of the Type and Length
             fields.

   Reserved  Sent as 0 and MUST be ignored on reception.

   Nonce     An arbitrary value that will be echoed in the receiver's
             Acknowledgement TLV.

   Interval  A time interval in centiseconds after which the sender will
             assume that this packet has been lost.  This MUST NOT be 0.
             The receiver MUST send an acknowledgement before this time
             has elapsed (with a margin allowing for propagation time).

4.4.4.  Acknowledgement

   0                   1                   2                   3
   0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |    Type = 3   |    Length     |            Nonce              |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

   This TLV is sent by a node upon receiving an Acknowledgement Request.

   Fields :

   Type      Set to 3 to indicate an Acknowledgement TLV.

   Length    The length of the body, exclusive of the Type and Length
             fields.





Chroboczek                    Experimental                     [Page 31]
RFC 6126               The Babel Routing Protocol             April 2011


   Nonce     Set to the Nonce value of the Acknowledgement Request that
             prompted this Acknowledgement.

   Since nonce values are not globally unique, this TLV MUST be sent to
   a unicast address.

4.4.5.  Hello

   0                   1                   2                   3
   0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |    Type = 4   |    Length     |          Reserved             |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |            Seqno              |          Interval             |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

   This TLV is used for neighbour discovery and for determining a link's
   reception cost.

   Fields :

   Type      Set to 4 to indicate a Hello TLV.

   Length    The length of the body, exclusive of the Type and Length
             fields.

   Reserved  Sent as 0 and MUST be ignored on reception.

   Seqno     The value of the sending node's Hello seqno for this
             interface.

   Interval  An upper bound, expressed in centiseconds, on the time
             after which the sending node will send a new Hello TLV.
             This MUST NOT be 0.

   Since there is a single seqno counter for all the Hellos sent by a
   given node over a given interface, this TLV MUST be sent to a
   multicast destination.  In order to avoid large discontinuities in
   link quality, multiple Hello TLVs SHOULD NOT be sent in the same
   packet.











Chroboczek                    Experimental                     [Page 32]
RFC 6126               The Babel Routing Protocol             April 2011


4.4.6.  IHU

   0                   1                   2                   3
   0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |    Type = 5   |    Length     |       AE      |    Reserved   |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |            Rxcost             |          Interval             |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |       Address...
   +-+-+-+-+-+-+-+-+-+-+-+-

   An IHU ("I Heard You") TLV is used for confirming bidirectional
   reachability and carrying a link's transmission cost.

   Fields :

   Type      Set to 5 to indicate an IHU TLV.

   Length    The length of the body, exclusive of the Type and Length
             fields.

   AE        The encoding of the Address field.  This should be 1 or 3
             in most cases.  As an optimisation, it MAY be 0 if the TLV
             is sent to a unicast address, if the association is over a
             point-to-point link, or when bidirectional reachability is
             ascertained by means outside of the Babel protocol.

   Reserved  Sent as 0 and MUST be ignored on reception.

   Rxcost    The rxcost according to the sending node of the interface
             whose address is specified in the Address field.  The value
             FFFF hexadecimal (infinity) indicates that this interface
             is unreachable.

   Interval  An upper bound, expressed in centiseconds, on the time
             after which the sending node will send a new IHU; this MUST
             NOT be 0.  The receiving node will use this value in order
             to compute a hold time for this symmetric association.

   Address   The address of the destination node, in the format
             specified by the AE field.  Address compression is not
             allowed.

   Conceptually, an IHU is destined to a single neighbour.  However, IHU
   TLVs contain an explicit destination address, and it SHOULD be sent
   to a multicast address, as this allows aggregation of IHUs destined




Chroboczek                    Experimental                     [Page 33]
RFC 6126               The Babel Routing Protocol             April 2011


   to distinct neighbours into a single packet and avoids the need for
   an ARP or Neighbour Discovery exchange when a neighbour is not being
   used for data traffic.

   IHU TLVs with an unknown value for the AE field MUST be silently
   ignored.

4.4.7.  Router-Id

   0                   1                   2                   3
   0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |    Type = 6   |    Length     |          Reserved             |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |                                                               |
   +                           Router-Id                           +
   |                                                               |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

   A Router-Id TLV establishes a router-id that is implied by subsequent
   Update TLVs.

   Fields :

   Type      Set to 6 to indicate a Router-Id TLV.

   Length    The length of the body, exclusive of the Type and Length
             fields.

   Reserved  Sent as 0 and MUST be ignored on reception.

   Router-Id The router-id for routes advertised in subsequent Update
             TLVs

4.4.8.  Next Hop

   0                   1                   2                   3
   0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |    Type = 7   |    Length     |      AE       |   Reserved    |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |       Next hop...
   +-+-+-+-+-+-+-+-+-+-+-+-

   A Next Hop TLV establishes a next-hop address for a given address
   family (IPv4 or IPv6) that is implied by subsequent Update TLVs.





Chroboczek                    Experimental                     [Page 34]
RFC 6126               The Babel Routing Protocol             April 2011


   Fields :

   Type      Set to 7 to indicate a Next Hop TLV.

   Length    The length of the body, exclusive of the Type and Length
             fields.

   AE        The encoding of the Address field.  This SHOULD be 1 or 3
             and MUST NOT be 0.

   Reserved  Sent as 0 and MUST be ignored on reception.

   Next hop  The next-hop address advertised by subsequent Update TLVs,
             for this address family.

   When the address family matches the network-layer protocol that this
   packet is transported over, a Next Hop TLV is not needed: in that
   case, the next hop is taken to be the source address of the packet.

   Next Hop TLVs with an unknown value for the AE field MUST be silently
   ignored.

4.4.9.  Update

   0                   1                   2                   3
   0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |    Type = 8   |    Length     |       AE      |    Flags      |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |     Plen      |    Omitted    |            Interval           |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |             Seqno             |            Metric             |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |      Prefix...
   +-+-+-+-+-+-+-+-+-+-+-+-

   An Update TLV advertises or retracts a route.  As an optimisation,
   this can also have the side effect of establishing a new implied
   router-id and a new default prefix.

   Fields :

   Type      Set to 8 to indicate an Update TLV.

   Length    The length of the body, exclusive of the Type and Length
             fields.

   AE        The encoding of the Prefix field.



Chroboczek                    Experimental                     [Page 35]
RFC 6126               The Babel Routing Protocol             April 2011


   Flags     The individual bits of this field specify special handling
             of this TLV (see below).  Every node MUST be able to
             interpret the flags with values 80 and 40 hexadecimal;
             unknown flags MUST be silently ignored.

   Plen      The length of the advertised prefix.

   Omitted   The number of octets that have been omitted at the
             beginning of the advertised prefix and that should be taken
             from a preceding Update TLV with the flag with value 80
             hexadecimal set.

   Interval  An upper bound, expressed in centiseconds, on the time
             after which the sending node will send a new update for
             this prefix.  This MUST NOT be 0 and SHOULD NOT be less
             than 10.  The receiving node will use this value to compute
             a hold time for this routing table entry.  The value FFFF
             hexadecimal (infinity) expresses that this announcement
             will not be repeated unless a request is received
             (Section 3.8.2.3).

   Seqno     The originator's sequence number for this update.

   Metric    The sender's metric for this route.  The value FFFF
             hexadecimal (infinity) means that this is a route
             retraction.

   Prefix    The prefix being advertised.  This field's size is (Plen/8
             - Omitted) rounded upwards.

   The Flags field is interpreted as follows:

   o  if the bit with value 80 hexadecimal is set, then this Update
      establishes a new default prefix for subsequent Update TLVs with a
      matching address family within the same packet;

   o  if the bit with value 40 hexadecimal is set, then the low-order 8
      octets of the advertised prefix establish a new default router-id
      for this TLV and subsequent Update TLVs in the same packet.

   The prefix being advertised by an Update TLV is computed as follows:

   o  the first Omitted octets of the prefix are taken from the previous
      Update TLV with flag 80 hexadecimal set and the same address
      family;

   o  the next (Plen/8 - Omitted) (rounded upwards) octets are taken
      from the Prefix field;



Chroboczek                    Experimental                     [Page 36]
RFC 6126               The Babel Routing Protocol             April 2011


   o  the remaining octets are set to 0.

   If the Metric field is finite, the router-id of the originating node
   for this announcement is taken from the low-order 8 octets of the
   prefix advertised by this Update if the bit with value 40 hexadecimal
   is set in the Flags field.  Otherwise, it is taken either from the
   preceding Router-Id packet, or the preceding Update packet with flag
   40 hexadecimal set, whichever comes last.

   The next-hop address for this update is taken from the last preceding
   Next Hop TLV with a matching address family in the same packet; if no
   such TLV exists, it is taken from the network-layer source address of
   this packet.

   If the metric field is FFFF hexadecimal, this TLV specifies a
   retraction.  In that case, the current router-id and the Seqno are
   not used.  AE MAY then be 0, in which case this Update retracts all
   of the routes previously advertised on this interface.

   Update TLVs with an unknown value for the AE field MUST be silently
   ignored.

4.4.10.  Route Request

   0                   1                   2                   3
   0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |    Type = 9   |    Length     |      AE       |     Plen      |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |      Prefix...
   +-+-+-+-+-+-+-+-+-+-+-+-

   A Route Request TLV prompts the receiver to send an update for a
   given prefix, or a full routing table dump.

   Fields :

   Type      Set to 9 to indicate a Route Request TLV.

   Length    The length of the body, exclusive of the Type and Length
             fields.

   AE        The encoding of the Prefix field.  The value 0 specifies
             that this is a request for a full routing table dump (a
             wildcard request).

   Plen      The length of the requested prefix.




Chroboczek                    Experimental                     [Page 37]
RFC 6126               The Babel Routing Protocol             April 2011


   Prefix    The prefix being requested.  This field's size is Plen/8
             rounded upwards.

   A Request TLV prompts the receiving node to send an update message
   for the prefix specified by the AE, Plen, and Prefix fields, or a
   full dump of its routing table if AE is 0 (in which case Plen MUST be
   0, and Prefix is of length 0).  A Request may be sent to a unicast
   address if it is destined to a single node, or to a multicast address
   if the request is destined to all of the neighbours of the sending
   interface.

4.4.11.  Seqno Request

   0                   1                   2                   3
   0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |    Type = 10  |    Length     |      AE       |    Plen       |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |             Seqno             |  Hop Count    |   Reserved    |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |                                                               |
   +                          Router-Id                            +
   |                                                               |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |   Prefix...
   +-+-+-+-+-+-+-+-+-+-+

   A Seqno Request TLV prompts the receiver to send an Update for a
   given prefix with a given sequence number, or to forward the request
   further if it cannot be satisfied locally.

   Fields :

   Type      Set to 10 to indicate a Seqno Request message.

   Length    The length of the body, exclusive of the Type and Length
             fields.

   AE        The encoding of the Prefix field.  This MUST NOT be 0.

   Plen      The length of the requested prefix.

   Seqno     The sequence number that is being requested.

   Hop Count The maximum number of times that this TLV may be forwarded,
             plus 1.  This MUST NOT be 0.





Chroboczek                    Experimental                     [Page 38]
RFC 6126               The Babel Routing Protocol             April 2011


   Prefix    The prefix being requested.  This field's size is Plen/8
             rounded upwards.

   A Seqno Request TLV prompts the receiving node to send an Update for
   the prefix specified by the AE, Plen, and Prefix fields, with either
   a router-id different from what is specified by the Router-Id field,
   or a Seqno no less than what is specified by the Seqno field.  If
   this request cannot be satisfied locally, then it is forwarded
   according to the rules set out in Section 3.8.1.2.

   While a Seqno Request MAY be sent to a multicast address, it MUST NOT
   be forwarded to a multicast address and MUST NOT be forwarded to more
   than one neighbour.  A request MUST NOT be forwarded if its Hop Count
   field is 1.

5.  IANA Considerations

   IANA has registered the UDP port number 6697, called "babel", for use
   by the Babel protocol.

   IANA has registered the IPv6 multicast group ff02:0:0:0:0:0:1:6 and
   the IPv4 multicast group 224.0.0.111 for use by the Babel protocol.

6.  Security Considerations

   As defined in this document, Babel is a completely insecure protocol.
   Any attacker can attract data traffic by advertising routes with a
   low metric.  This particular issue can be solved either by lower-
   layer security mechanisms (e.g., IPsec or link-layer security), or by
   appending a cryptographic key to Babel packets; the provision of
   ignoring any data contained within a Babel packet beyond the body
   length declared by the header is designed for just such a purpose.

   The information that a Babel node announces to the whole routing
   domain is often sufficient to determine a mobile node's physical
   location with reasonable precision.  The privacy issues that this
   causes can be mitigated somewhat by using randomly chosen router-ids
   and randomly chosen IP addresses, and changing them periodically.

   When carried over IPv6, Babel packets are ignored unless they are
   sent from a link-local IPv6 address; since routers don't forward
   link-local IPv6 packets, this provides protection against spoofed
   Babel packets being sent from the global Internet.  No such natural
   protection exists when Babel packets are carried over IPv4.







Chroboczek                    Experimental                     [Page 39]
RFC 6126               The Babel Routing Protocol             April 2011


7.  References

7.1.  Normative References

   [ADDRARCH]  Hinden, R. and S. Deering, "IP Version 6 Addressing
               Architecture", RFC 4291, February 2006.

   [RFC2119]   Bradner, S., "Key words for use in RFCs to Indicate
               Requirement Levels", BCP 14, RFC 2119, March 1997.

7.2.  Informative References

   [DSDV]      Perkins, C. and P. Bhagwat, "Highly Dynamic Destination-
               Sequenced Distance-Vector Routing (DSDV) for Mobile
               Computers", ACM SIGCOMM'94 Conference on Communications
               Architectures, Protocols and Applications 234-244, 1994.

   [DUAL]      Garcia Luna Aceves, J., "Loop-Free Routing Using
               Diffusing Computations", IEEE/ACM Transactions on
               Networking 1:1, February 1993.

   [EIGRP]     Albrightson, B., Garcia Luna Aceves, J., and J. Boyle,
               "EIGRP -- a Fast Routing Protocol Based on Distance
               Vectors", Proc. Interop 94, 1994.

   [ETX]       De Couto, D., Aguayo, D., Bicket, J., and R. Morris, "A
               high-throughput path metric for multi-hop wireless
               networks", Proc. MobiCom 2003, 2003.

   [IS-IS]     "Information technology -- Telecommunications and
               information exchange between systems -- Intermediate
               System to Intermediate System intra-domain routeing
               information exchange protocol for use in conjunction with
               the protocol for providing the connectionless-mode
               network service (ISO 8473)", ISO/IEC 10589:2002.

   [JITTER]    Floyd, S. and V. Jacobson, "The synchronization of
               periodic routing messages", IEEE/ACM Transactions on
               Networking 2, 2, 122-136, April 1994.

   [OSPF]      Moy, J., "OSPF Version 2", STD 54, RFC 2328, April 1998.

   [PACKETBB]  Clausen, T., Dearlove, C., Dean, J., and C. Adjih,
               "Generalized Mobile Ad Hoc Network (MANET) Packet/Message
               Format", RFC 5444, February 2009.

   [RIP]       Malkin, G., "RIP Version 2", STD 56, RFC 2453,
               November 1998.



Chroboczek                    Experimental                     [Page 40]
RFC 6126               The Babel Routing Protocol             April 2011


Appendix A.  Cost and Metric Computation

   The strategy for computing link costs and route metrics is a local
   matter; Babel itself only requires that it comply with the conditions
   given in Sections 3.4.3 and 3.5.2.  Different nodes MAY use different
   strategies in a single network and MAY use different strategies on
   different interface types.  This section gives a few examples of such
   strategies.

   The sample implementation of Babel maintains statistics about the
   last 16 received Hello TLVs (Appendix A.1), computes costs by using
   the 2-out-of-3 strategy (Appendix A.2.1) on wired links, and ETX
   [ETX] on wireless links.  It uses an additive algebra for metric
   computation (Appendix A.3.1).

A.1.  Maintaining Hello History

   For each neighbour, the sample implementation of Babel maintains a
   Hello history and an expected sequence number.  The Hello history is
   a vector of 16 bits, where a 1 value represents a received Hello, and
   a 0 value a missed Hello.  The expected sequence number, written ne,
   is the sequence number that is expected to be carried by the next
   received hello from this neighbour.

   Whenever it receives a Hello packet from a neighbour, a node compares
   the received sequence number nr with its expected sequence number ne.
   Depending on the outcome of this comparison, one of the following
   actions is taken:

   o  if the two differ by more than 16 (modulo 2^16), then the sending
      node has probably rebooted and lost its sequence number; the
      associated neighbour table entry is flushed;

   o  otherwise, if the received nr is smaller (modulo 2^16) than the
      expected sequence number ne, then the sending node has increased
      its Hello interval without our noticing; the receiving node
      removes the last (ne - nr) entries from this neighbour's Hello
      history (we "undo history");

   o  otherwise, if nr is larger (modulo 2^16) than ne, then the sending
      node has decreased its Hello interval, and some Hellos were lost;
      the receiving node adds (nr - ne) 0 bits to the Hello history (we
      "fast-forward").








Chroboczek                    Experimental                     [Page 41]
RFC 6126               The Babel Routing Protocol             April 2011


   The receiving node then appends a 1 bit to the neighbour's Hello
   history, resets the neighbour's Hello timer, and sets ne to (nr + 1).
   It then resets the neighbour's Hello timer to 1.5 times the value
   advertised in the received Hello (the extra margin allows for the
   delay due to jitter).

   Whenever the Hello timer associated to a neighbour expires, the local
   node adds a 0 bit to this neighbour's Hello history, and increments
   the expected Hello number.  If the Hello history is empty (it
   contains 0 bits only), the neighbour entry is flushed; otherwise, it
   resets the neighbour's Hello timer to the value advertised in the
   last Hello received from this neighbour (no extra margin is necessary
   in this case).

A.2.  Cost Computation

A.2.1.  k-out-of-j

   K-out-of-j link sensing is suitable for wired links that are either
   up, in which case they only occasionally drop a packet, or down, in
   which case they drop all packets.

   The k-out-of-j strategy is parameterised by two small integers k and
   j, such that 0 < k <= j, and the nominal link cost, a constant K >=
   1.  A node keeps a history of the last j hellos; if k or more of
   those have been correctly received, the link is assumed to be up, and
   the rxcost is set to K; otherwise, the link is assumed to be down,
   and the rxcost is set to infinity.

   The cost of such a link is defined as

   o  cost = FFFF hexadecimal if rxcost = FFFF hexadecimal;

   o  cost = txcost otherwise.

A.2.2.  ETX

   The Estimated Transmission Cost metric [ETX] estimates the number of
   times that a unicast frame will be retransmitted by the IEEE 802.11
   MAC, assuming infinite persistence.

   A node uses a neighbour's Hello history to compute an estimate,
   written beta, of the probability that a Hello TLV is successfully
   received.  The rxcost is defined as 256/beta.

   Let alpha be MIN(1, 256/txcost), an estimate of the probability of
   successfully sending a Hello TLV.  The cost is then computed by




Chroboczek                    Experimental                     [Page 42]
RFC 6126               The Babel Routing Protocol             April 2011


      cost = 256/(alpha * beta)

   or, equivalently,

      cost = (MAX(txcost, 256) * rxcost) / 256.

A.3.  Metric Computation

A.3.1.  Additive Metrics

   The simplest approach for obtaining a monotonic, isotonic metric is
   to define the metric of a route as the sum of the costs of the
   component links.  More formally, if a neighbour advertises a route
   with metric m over a link with cost c, then the resulting route has
   metric M(c, m) = c + m.

   A multiplicative metric can be converted to an additive one by taking
   the logarithm (in some suitable base) of the link costs.

A.3.2.  External Sources of Willingness

   A node may want to vary its willingness to forward packets by taking
   into account information that is external to the Babel protocol, such
   as the monetary cost of a link, the node's battery status, CPU load,
   etc.  This can be done by adding to every route's metric a value k
   that depends on the external data.  For example, if a battery-powered
   node receives an update with metric m over a link with cost c, it
   might compute a metric M(c, m) = k + c + m, where k depends on the
   battery status.

   In order to preserve strict monotonicity (Section 3.5.2), the value k
   must be greater than -c.

Appendix B.  Constants

   The choice of time constants is a trade-off between fast detection of
   mobility events and protocol overhead.  Two implementations of Babel
   with different time constants will interoperate, although the
   resulting convergence time will most likely be dictated by the
   slowest of the two implementations.

   Experience with the sample implementation of Babel indicates that the
   Hello interval is the most important time constant: a mobility event
   is detected within 1.5 to 3 Hello intervals.  Due to Babel's reliance
   on triggered updates and explicit requests, the Update interval only
   has an effect on the time it takes for accurate metrics to be
   propagated after variations in link costs too small to trigger an
   unscheduled update.



Chroboczek                    Experimental                     [Page 43]
RFC 6126               The Babel Routing Protocol             April 2011


   At the time of writing, the sample implementation of Babel uses the
   following default values:

      Hello Interval: 4 seconds on wireless links, 20 seconds on wired
      links.

      IHU Interval: the advertised IHU interval is always 3 times the
      Hello interval.  IHUs are actually sent with each Hello on lossy
      links (as determined from the Hello history), but only with every
      third Hello on lossless links.

      Update Interval: 4 times the Hello interval.

      IHU Hold Time: 3.5 times the advertised IHU interval.

      Route Expiry Time: 3.5 times the advertised update interval.

      Source GC time: 3 minutes.

   The amount of jitter applied to a packet depends on whether it
   contains any urgent TLVs or not.  Urgent triggered updates and urgent
   requests are delayed by no more than 200 ms; other TLVs are delayed
   by no more than one-half the Hello interval.

Appendix C.  Simplified Implementations

   Babel is a fairly economic protocol.  Route updates take between 12
   and 40 octets per destination, depending on how successful
   compression is; in a double-stack mesh network, an average of less
   than 24 octets is typical.  The route table occupies about 35 octets
   per IPv6 entry.  To put these values into perspective, a single full-
   size Ethernet frame can carry some 65 route updates, and a megabyte
   of memory can contain a 20000-entry routing table and the associated
   source table.

   Babel is also a reasonably simple protocol.  The sample
   implementation consists of less than 8000 lines of C code, and it
   compiles to less than 60 kB of text on a 32-bit CISC architecture.

   Nonetheless, in some very constrained environments, such as PDAs,
   microwave ovens, or abacuses, it may be desirable to have subset
   implementations of the protocol.

   A parasitic implementation is one that uses a Babel network for
   routing its packets but does not announce any of the routes that it
   has learnt from its neighbours.  (This is slightly more than a
   passive implementation, which doesn't even announce routes to
   itself.)  It may either maintain a full routing table or simply



Chroboczek                    Experimental                     [Page 44]
RFC 6126               The Babel Routing Protocol             April 2011


   select a gateway amongst any one of its neighbours that announces a
   default route.  Since a parasitic implementation never forwards
   packets, it cannot possibly participate in a routing loop; hence, it
   need not evaluate the feasibility condition and need not maintain a
   source table.

   A parasitic implementation MUST answer acknowledgement requests and
   MUST participate in the Hello/IHU protocol.  Finally, it MUST be able
   to reply to seqno requests for routes that it announces and SHOULD be
   able to reply to route requests.

Appendix D.  Software Availability

   The sample implementation of Babel is available from
   <http://www.pps.jussieu.fr/~jch/software/babel/>.

Author's Address

   Juliusz Chroboczek
   PPS, University of Paris 7
   Case 7014
   75205 Paris Cedex 13,
   France

   EMail: jch@pps.jussieu.fr


























Chroboczek                    Experimental                     [Page 45]
  1. RFC 6126