Home

RFC5450

  1. RFC 5450
Network Working Group                                          D. Singer
Request for Comments: 5450                           Apple Computer Inc.
Category: Standards Track                                    H. Desineni
                                                                Qualcomm
                                                              March 2009


                Transmission Time Offsets in RTP Streams

Status of This Memo

   This document specifies an Internet standards track protocol for the
   Internet community, and requests discussion and suggestions for
   improvements.  Please refer to the current edition of the "Internet
   Official Protocol Standards" (STD 1) for the standardization state
   and status of this protocol.  Distribution of this memo is unlimited.

Copyright Notice

   Copyright (c) 2009 IETF Trust and the persons identified as the
   document authors.  All rights reserved.

   This document is subject to BCP 78 and the IETF Trust's Legal
   Provisions Relating to IETF Documents in effect on the date of
   publication of this document (http://trustee.ietf.org/license-info).
   Please review these documents carefully, as they describe your rights
   and restrictions with respect to this document.

   This document may contain material from IETF Documents or IETF
   Contributions published or made publicly available before November
   10, 2008.  The person(s) controlling the copyright in some of this
   material may not have granted the IETF Trust the right to allow
   modifications of such material outside the IETF Standards Process.
   Without obtaining an adequate license from the person(s) controlling
   the copyright in such materials, this document may not be modified
   outside the IETF Standards Process, and derivative works of it may
   not be created outside the IETF Standards Process, except to format
   it for publication as an RFC or to translate it into languages other
   than English.

Abstract

   This document describes a method to inform Real-time Transport
   Protocol (RTP) clients when RTP packets are transmitted at a time
   other than their 'nominal' transmission time.  It also provides a
   mechanism to provide improved inter-arrival jitter reports from the
   clients, that take into account the reported transmission times.




Singer & Desineni           Standards Track                     [Page 1]
RFC 5450                RTP Transmission Offsets              March 2009


Table of Contents

   1.  Introduction  . . . . . . . . . . . . . . . . . . . . . . . . . 2
   2.  Requirements Notation . . . . . . . . . . . . . . . . . . . . . 3
   3.  Transmission Offset . . . . . . . . . . . . . . . . . . . . . . 3
   4.  Extended Jitter Reports . . . . . . . . . . . . . . . . . . . . 5
   5.  Signaling (Setup) Information . . . . . . . . . . . . . . . . . 6
   6.  Security Considerations . . . . . . . . . . . . . . . . . . . . 6
   7.  IANA Considerations . . . . . . . . . . . . . . . . . . . . . . 7
   8.  Acknowledgments . . . . . . . . . . . . . . . . . . . . . . . . 7
   9.  Normative References  . . . . . . . . . . . . . . . . . . . . . 7

1.  Introduction

   In the Real-time Transport Protocol (RTP) specification [RFC3550],
   network jitter calculations are based on the presumption that packets
   are transmitted essentially in accordance with their RTP timestamps.
   This must be true, of course, on average over longer time intervals,
   as the client is playing the packets out according to those
   timestamps.  However, for individual packets, this may not be true
   under some circumstances, such as:

   o  When the data rate of the stream is bursty, such as with video
      where I-frames may be significantly larger than P or B frames,
      traffic smoothing may need to be applied to maintain an
      appropriate data rate.

   o  In video that has forward-decode dependencies, frames may need to
      be transmitted in decoding order (the sequence number order) but
      with, of course, presentation timestamps.  Under these
      circumstances, the transmission time of a frame sent early in
      sequence does not correspond to its RTP timestamp.

   o  When retransmissions are sent, the retransmitted packet clearly
      has a different actual transmission time from the original, even
      though they share the same timestamp.

   Under some circumstances, it can help the receiver, or intermediate
   network elements, to know the actual transmission time of the packet.
   This RTP header extension element allows the communication of this
   information.

   The RTP specification does not define a transmission timestamp; nor
   does this specification.  This specification merely provides
   information on the relationship between the relative transmission
   times and relative RTP timestamps.





Singer & Desineni           Standards Track                     [Page 2]
RFC 5450                RTP Transmission Offsets              March 2009


   This specification allows the transmitter to indicate to the receiver
   any known variation between the spacing of transmission times and the
   spacing of RTP timestamps; any unreported variation introduced at or
   after the point of measurement of the transmission time will be
   treated as network jitter by the receiver.  The definition of the
   point where the transmission time is measured or defined is left to
   the transmitter, though it should, of course, be consistent from
   packet to packet.

   This information can also be of use to report the inter-arrival
   jitter caused by the network, excluding that introduced by the
   source.  A new RTP Control Protocol (RTCP) packet is defined to
   enable this reporting.

2.  Requirements Notation

   The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
   "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
   document are to be interpreted as described in [RFC2119].

3.  Transmission Offset

   Classically, a pair of RTP packets with timestamps S2 and S1 are
   transmitted with a time interval between them of (S2 - S1).  This
   specification permits sending an offset value O in each packet, O1
   and O2.  One characteristic of these offsets is that the original
   transmission interval can be deduced to be (S2 + O2) - (S1 + O1).

   More precisely, the offset is defined as follows (with the function
   RtoN converting from RTP to Network Time Protocol (NTP) times, and
   NtoR doing the reverse):

   o  Take an RTP stream that has a recent RTCP sender report relating
      RTP timestamp S0 to NTP timestamp N0;

   o  Consider a packet sent after that with RTP timestamp S1.
      Nominally, this is sent at N1 = (N0 + RtoN(S1 - S0));

   o  If it was actually sent at a different time, Na, then the offset
      value O1 is O1 = NtoR(Na - N1).

   The transmission time is signaled to the receiver in-band using the
   general mechanism for RTP header extensions [RFC5285].  The payload
   of this extension (the transmitted value) is a 24-bit signed integer.
   When added to the RTP timestamp of the packet, it represents the
   "effective" RTP transmission time of the packet, on the RTP
   timescale.  The reported transmission time T1 of a packet with




Singer & Desineni           Standards Track                     [Page 3]
RFC 5450                RTP Transmission Offsets              March 2009


   timestamp S1 and an offset of O1, from the above equations, is T1 =
   S1+O1 (though of course the transmission time values only have
   meaning when two or more are compared).

   The form of the transmission offset extension block is as follows:

       0                   1                   2                   3
       0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |  ID   | len=2 |              transmission offset              |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

   The length field takes the value 2 to indicate that 3 bytes follow.

   The sign of the offset value depends greatly on the choice of the
   initial mapping of RTP to NTP times.  In general, without scanning a
   stream entirely it is not possible to ensure that this mapping would
   keep all the offsets positive; therefore, this specification allows
   negative values.

   Imagine a stream with the following timestamps and sizes (in KB):

   200    2 KB
   300    4 KB
   400    2 KB
   500   12 KB
   600   ...effective end of stream

   This has 20 KB spread over 400 time units, i.e., on average, 1 KB per
   20 time units.  We traffic-smooth this, and establish that given a
   transmission time of x for the first packet, we would transmit the
   following packets at the given intervals later:

   x + 000   2 KB
   x + 040   4 KB
   x + 120   2 KB
   x + 160  12 KB
   x + 400 ...effective end of stream

   The choice of x is essentially arbitrary: only relative values of
   timestamps matter.  Now, let's say I claim on the first packet that
   it went out *at* its RTP timestamp, i.e., with an offset of 0,
   meaning that x is 200.  Then the offset values are:

      0
    -60
    -80
   -140



Singer & Desineni           Standards Track                     [Page 4]
RFC 5450                RTP Transmission Offsets              March 2009


   This is because in this case, I traffic-smooth by conceptually
   sending the small packets 'early'.  But since only the relative
   values are significant, it is just as valid to say x is 400,
   whereupon the offset values are:

   200
   140
   120
    60

   In a stream where this extension is not in effect (i.e., not declared
   or negotiated), the actual transmission offset is therefore unknown.
   However, when the extension is in effect for the stream, it MAY be
   omitted in those packets for which the offset is 0 (zero); that is,
   packets sent at their nominal time do not need this to be tagged with
   this extension.  Therefore, the implied transmission time of an un-
   tagged RTP packet depends on whether the extension is in effect for
   the stream (and therefore the transmission offset is 0) or not
   (whereupon the transmission offset is unknown).

   The jitter calculations performed by an RTP client MUST NOT use these
   transmission offsets.  In general, the sender (or intermediate
   network elements doing RTP analysis) cannot always know whether the
   offsets have been taken into account or not.  Therefore, for
   consistency, the jitter calculation should continue to operate on the
   'raw' reception times.  However, see Section 4 on extended jitter
   reports, below.

   There are no extensionattributes defined for this extension.

   It is structurally possible to have more than one extension of the
   same type in a packet.  However, this extension is only defined for
   the source to report.  Intermediate network nodes that are not the
   source of the RTP session MUST NOT add this extension (whether or not
   it was previously present) and MUST NOT alter the existing
   transmission offset value in a packet, if the extension is already
   present.

   (Of course, it is clear that network elements that terminate an RTP
   flow, and are the source for a new RTP flow, can add a transmission
   offset extension header to the RTP packets of the new flow, if
   desired.)

4.  Extended Jitter Reports

   The inter-arrival jitter computed as defined in Section 6.4.1 of RFC
   3550 provides inter-arrival jitter reports that include any source-
   introduced jitter (transmission time offsets).  If it is desired to



Singer & Desineni           Standards Track                     [Page 5]
RFC 5450                RTP Transmission Offsets              March 2009


   indicate the actual network jitter, excluding the source-introduced
   jitter, the new RTCP packet type defined here may be used.

   It has the following form:

        0                   1                   2                   3
        0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
       +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   hdr |V=2|P|    RC   |   PT=IJ=195   |             length            |
       +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
       |                      inter-arrival jitter                     |
       +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
       .                                                               .
       .                                                               .
       .                                                               .
       |                      inter-arrival jitter                     |
       +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

   If present, this RTCP packet must be placed after a receiver report
   (inside a compound RTCP packet), and MUST have the same value for RC
   (reception report count) as the receiver report.  The content is
   exactly that number of inter-arrival jitter calculations, calculated
   using the same formula as for sender and receiver reports, but taking
   into account the transmission offsets for the streams (if any).  That
   is, the formula uses the values T1=S1+O1, T2, etc., as defined above,
   instead of S1, S2, etc.  (If no transmission offset information is
   given for a stream, then the value of inter-arrival jitter in this
   packet and in the receiver report will be identical).

   Precisely, the replacement equation for the equation in the RTP
   specification is as follows, where Rj is the most recent arrival
   time:

   D(i,j) = (Rj - Ri) - ((Sj + Oj) - (Si + Oi))
          = (Rj - (Sj + Oj)) - (Ri - (Si + Oi))

5.  Signaling (Setup) Information

   The URI for declaring this header extension in an extmap attribute is
   "urn:ietf:params:rtp-hdrext:toffset".  There is no additional setup
   information needed for this extension (no extensionattributes).

6.  Security Considerations

   The given transmission offsets are only informative, and it is hard
   to see security considerations from associating them with media
   streams.




Singer & Desineni           Standards Track                     [Page 6]
RFC 5450                RTP Transmission Offsets              March 2009


   The underlying security considerations of [RFC3550] should be taken
   into account.

   It is possible that malicious senders (or systems tampering with
   packets in transit) could send offsets that are implausible, could
   confuse the receiver, or result in calculated jitter values that
   might mislead the sender.  Both the sender and receiver of the
   transmission offsets and jitter values should take care that such
   behavior does not result in denial of service or other problems.

7.  IANA Considerations

   The RTCP packet type used for the adjusted inter-arrival jitter has
   been registered, in accordance with Section 15 of [RFC3550].  IANA
   has added a new value to the RTCP Control Packet types subregistry of
   the Real-Time Transport Protocol (RTP) Parameters registry, according
   to the following data:

   abbrev.  name                                  value   Reference
   -------  ------------------------------------  ------  ---------
   IJ       Extended inter-arrival jitter report  195     RFC 5450

   Additionally, IANA has registered a new extension URI to the RTP
   Compact Header Extensions subregistry of the Real-Time Transport
   Protocol (RTP) Parameters registry, according to the following data:

      Extension URI: urn:ietf:params:rtp-hdrext:toffset
      Description:   Transmission Time offsets
      Contact:       singer@apple.com
      Reference:     RFC 5450

8.  Acknowledgments

   Ron Frederick, Colin Perkins, and Steve Casner all contributed
   substantially to this document, and their help and contributions
   helped turn an idea into a specification.

9.  Normative References

   [RFC2119]  Bradner, S., "Key words for use in RFCs to Indicate
              Requirement Levels", BCP 14, RFC 2119, March 1997.

   [RFC3550]  Schulzrinne, H., Casner, S., Frederick, R., and V.
              Jacobson, "RTP: A Transport Protocol for Real-Time
              Applications", STD 64, RFC 3550, July 2003.

   [RFC5285]  Singer, D. and H. Desineni, "A General Mechanism for RTP
              Header Extensions", RFC 5285, July 2008.



Singer & Desineni           Standards Track                     [Page 7]
RFC 5450                RTP Transmission Offsets              March 2009


Authors' Addresses

   David Singer
   Apple Computer Inc.
   1 Infinite Loop
   Cupertino, CA  95014
   US

   Phone: +1 408 996 1010
   EMail: singer@apple.com


   Harikishan Desineni
   Qualcomm
   5775 Morehouse Drive
   San Diego, CA  92121
   US

   Phone: +1 858 845 8996
   EMail: hd@qualcomm.com































Singer & Desineni           Standards Track                     [Page 8]
  1. RFC 5450