Lisp Workgroup RFCs

Browse Lisp Workgroup RFCs by Number

RFC6830 - The Locator/ID Separation Protocol (LISP)
This document describes a network-layer-based protocol that enables separation of IP addresses into two new numbering spaces: Endpoint Identifiers (EIDs) and Routing Locators (RLOCs). No changes are required to either host protocol stacks or to the "core" of the Internet infrastructure. The Locator/ID Separation Protocol (LISP) can be incrementally deployed, without a "flag day", and offers Traffic Engineering, multihoming, and mobility benefits to early adopters, even when there are relatively few LISP-capable sites.
Design and development of LISP was largely motivated by the problem statement produced by the October 2006 IAB Routing and Addressing Workshop. This document defines an Experimental Protocol for the Internet community.
RFC6831 - The Locator/ID Separation Protocol (LISP) for Multicast Environments
This document describes how inter-domain multicast routing will function in an environment where Locator/ID Separation is deployed using the Locator/ID Separation Protocol (LISP) architecture. This document defines an Experimental Protocol for the Internet community.
RFC6832 - Interworking between Locator/ID Separation Protocol (LISP) and Non-LISP Sites
This document describes techniques for allowing sites running the Locator/ID Separation Protocol (LISP) to interoperate with Internet sites that may be using either IPv4, IPv6, or both but that are not running LISP. A fundamental property of LISP-speaking sites is that they use Endpoint Identifiers (EIDs), rather than traditional IP addresses, in the source and destination fields of all traffic they emit or receive. While EIDs are syntactically identical to IPv4 or IPv6 addresses, normally routes to them are not carried in the global routing system, so an interoperability mechanism is needed for non- LISP-speaking sites to exchange traffic with LISP-speaking sites. This document introduces three such mechanisms. The first uses a new network element, the LISP Proxy Ingress Tunnel Router (Proxy-ITR), to act as an intermediate LISP Ingress Tunnel Router (ITR) for non-LISP- speaking hosts. Second, this document adds Network Address Translation (NAT) functionality to LISP ITRs and LISP Egress Tunnel Routers (ETRs) to substitute routable IP addresses for non-routable EIDs. Finally, this document introduces the Proxy Egress Tunnel Router (Proxy-ETR) to handle cases where a LISP ITR cannot send packets to non-LISP sites without encapsulation. This document defines an Experimental Protocol for the Internet community.
RFC6833 - Locator/ID Separation Protocol (LISP) Map-Server Interface
This document describes the Mapping Service for the Locator/ID Separation Protocol (LISP), implemented by two new types of LISP- speaking devices -- the LISP Map-Resolver and LISP Map-Server -- that provides a simplified "front end" for one or more Endpoint ID to Routing Locator mapping databases.
By using this service interface and communicating with Map-Resolvers and Map-Servers, LISP Ingress Tunnel Routers and Egress Tunnel Routers are not dependent on the details of mapping database systems, which facilitates experimentation with different database designs. Since these devices implement the "edge" of the LISP infrastructure, connect directly to LISP-capable Internet end sites, and comprise the bulk of LISP-speaking devices, reducing their implementation and operational complexity should also reduce the overall cost and effort of deploying LISP. This document defines an Experimental Protocol for the Internet community.
RFC6834 - Locator/ID Separation Protocol (LISP) Map-Versioning
This document describes the LISP (Locator/ID Separation Protocol) Map-Versioning mechanism, which provides in-packet information about Endpoint ID to Routing Locator (EID-to-RLOC) mappings used to encapsulate LISP data packets. The proposed approach is based on associating a version number to EID-to-RLOC mappings and the transport of such a version number in the LISP-specific header of LISP-encapsulated packets. LISP Map-Versioning is particularly useful to inform communicating Ingress Tunnel Routers (ITRs) and Egress Tunnel Routers (ETRs) about modifications of the mappings used to encapsulate packets. The mechanism is transparent to implementations not supporting this feature, since in the LISP- specific header and in the Map Records, bits used for Map-Versioning can be safely ignored by ITRs and ETRs that do not support the mechanism. This document defines an Experimental Protocol for the Internet community.
RFC6835 - The Locator/ID Separation Protocol Internet Groper (LIG)
A simple tool called the Locator/ID Separation Protocol (LISP) Internet Groper or 'lig' can be used to query the LISP mapping database. This document describes how it works. This document is not an Internet Standards Track specification; it is published for informational purposes.
RFC6836 - Locator/ID Separation Protocol Alternative Logical Topology (LISP+ALT)
This document describes a simple distributed index system to be used by a Locator/ID Separation Protocol (LISP) Ingress Tunnel Router (ITR) or Map-Resolver (MR) to find the Egress Tunnel Router (ETR) that holds the mapping information for a particular Endpoint Identifier (EID). The MR can then query that ETR to obtain the actual mapping information, which consists of a list of Routing Locators (RLOCs) for the EID. Termed the Alternative Logical Topology (ALT), the index is built as an overlay network on the public Internet using the Border Gateway Protocol (BGP) and Generic Routing Encapsulation (GRE). This document defines an Experimental Protocol for the Internet community.
RFC7052 - Locator/ID Separation Protocol (LISP) MIB
This document defines the MIB module that contains managed objects to support the monitoring devices of the Locator/ID Separation Protocol (LISP). These objects provide information useful for monitoring LISP devices, including determining basic LISP configuration information, LISP functional status, and operational counters and other statistics.
RFC7215 - Locator/Identifier Separation Protocol (LISP) Network Element Deployment Considerations
This document is a snapshot of different Locator/Identifier Separation Protocol (LISP) deployment scenarios. It discusses the placement of new network elements introduced by the protocol, representing the thinking of the LISP working group as of Summer 2013. LISP deployment scenarios may have evolved since then. This memo represents one stable point in that evolution of understanding.