Home

Ancp Workgroup RFCs

Browse Ancp Workgroup RFCs by Number

RFC5713 - Security Threats and Security Requirements for the Access Node Control Protocol (ANCP)
The Access Node Control Protocol (ANCP) aims to communicate Quality of Service (QoS)-related, service-related, and subscriber-related configurations and operations between a Network Access Server (NAS) and an Access Node (e.g., a Digital Subscriber Line Access Multiplexer (DSLAM)). The main goal of this protocol is to allow the NAS to configure, manage, and control access equipment, including the ability for the Access Nodes to report information to the NAS.
This present document investigates security threats that all ANCP nodes could encounter. This document develops a threat model for ANCP security, with the aim of deciding which security functions are required. Based on this, security requirements regarding the Access Node Control Protocol are defined. This document is not an Internet Standards Track specification; it is published for informational purposes.
RFC5851 - Framework and Requirements for an Access Node Control Mechanism in Broadband Multi-Service Networks
The purpose of this document is to define a framework for an Access Node Control Mechanism between a Network Access Server (NAS) and an Access Node (e.g., a Digital Subscriber Line Access Multiplexer (DSLAM)) in a multi-service reference architecture in order to perform operations related to service, quality of service, and subscribers. The Access Node Control Mechanism will ensure that the transmission of the information does not need to go through distinct element managers but rather uses a direct device-device communication. This allows for performing access-link-related operations within those network elements, while avoiding impact on the existing Operational Support Systems.
This document first identifies a number of use cases for which the Access Node Control Mechanism may be appropriate. It then presents the requirements for the Access Node Control Protocol (ANCP) that must be taken into account during protocol design. Finally, it describes requirements for the network elements that need to support ANCP and the described use cases. These requirements should be seen as guidelines rather than as absolute requirements. RFC 2119 therefore does not apply to the nodal requirements. This document is not an Internet Standards Track specification; it is published for informational purposes.
RFC6320 - Protocol for Access Node Control Mechanism in Broadband Networks
This document describes the Access Node Control Protocol (ANCP). ANCP operates between a Network Access Server (NAS) and an Access Node (e.g., a Digital Subscriber Line Access Multiplexer (DSLAM)) in a multi-service reference architecture in order to perform operations related to Quality of Service, service, and subscribers. Use cases for ANCP are documented in RFC 5851. As well as describing the base ANCP protocol, this document specifies capabilities for Digital Subscriber Line (DSL) topology discovery, line configuration, and remote line connectivity testing. The design of ANCP allows for protocol extensions in other documents if they are needed to support other use cases and other access technologies.
ANCP is based on the General Switch Management Protocol version 3 (GSMPv3) described in RFC 3292, but with many modifications and extensions, to the point that the two protocols are not interoperable. For this reason, ANCP was assigned a separate version number to distinguish it. [STANDARDS-TRACK]
RFC6934 - Applicability of the Access Node Control Mechanism to Broadband Networks Based on Passive Optical Networks (PONs)
The purpose of this document is to provide applicability of the Access Node Control Mechanism to broadband access based on Passive Optical Networks (PONs). The need for an Access Node Control Mechanism between a Network Access Server (NAS) and an Access Node Complex, composed of a combination of Optical Line Termination (OLT) and Optical Network Termination (ONT) elements, is described in a multi-service reference architecture in order to perform QoS-related, service-related, and subscriber-related operations. The Access Node Control Mechanism is also extended for interaction between components of the Access Node Complex (OLT and ONT). The Access Node Control Mechanism will ensure that the transmission of information between the NAS and Access Node Complex (ANX) and between the OLT and ONT within an ANX does not need to go through distinct element managers but rather uses direct device-to-device communication and stays on net. This allows for performing access-link-related operations within those network elements to meet performance objectives.
RFC7256 - Multicast Control Extensions for the Access Node Control Protocol (ANCP)
This document specifies the extensions to the Access Node Control Protocol (ANCP) (RFC 6320) required for support of the multicast use cases defined in the Access Node Control Protocol framework document (RFC 5851) and one additional use case described in this document. These use cases are organized into the following ANCP capabilities:
o multicast replication initiated by the Network Access Server (NAS);
o conditional access and admission control with white and black lists;
o conditional access and admission control with grey lists;
o bandwidth delegation; and
o committed bandwidth reporting.
These capabilities may be combined according to the rules given in this specification.
This document updates RFC 6320 by assigning capability type 3 to a capability specified in this document and by changing the starting point for IANA allocation of result codes determined by IETF Consensus from 0x100 to 0x64.